Raypak 133-4001 manual Outdoor Boilers, High-Wind Conditions Outdoor Units Only

Page 8

NOTE: The boiler shall be installed in a space large in comparison to the size of the boiler. Large space is defined as having a volume at least sixteen (16) times the total volume of the boiler.

Outdoor Boilers

These boilers are design certified for outdoor installa- tion. Boilers must not be installed under an overhang within three (3) feet from the top on the boiler. Three

(3)sides must be open in the area under the over- hang. Roof water drainage must be diverted away from the boilers with the use of gutters.

The point from where the flue products exit the boiler must be a minimum of four (4) feet below, four (4) feet horizontally from or one (1) foot above any door, win- dow or gravity inlet to a building. The top surface of the boiler shall be at least three (3) feet above any forced air inlet, or intake ducts located within ten (10) feet hor- izontally.

Derived from National Fuel Gas Code, Table 6.2.3(b)

Table D: Reduction of Clearances to Protected

Surfaces

Fig. 3: Minimum Distances to Building Openings from

Where Flue Products Exit the Boiler

High-Wind Conditions (Outdoor Units Only)

In areas where high winds are frequent, it may be nec- essary to locate the boiler a minimum of 3' from high vertical walls, or install a wind break so the boiler is not in direct wind current.

Combustion and Ventilation Air (Indoor Units Only)

The boiler must have both combustion and ventilation air. Minimum requirements for net free air supply openings are 12 inches from ceiling for ventilation and 12 inches from the floor for combustion air as outlined in Z223.1 - latest edition or the current CAN/CSA B149, as well as any local codes that may

have jurisdiction.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Raytherm Heating Boilers Deletions None Contents Are important but not related to personal injury hazards Model Identification 0 5 1 4 aInstallation Receiving EquipmentCertifications Boiler TypesInstallation Base ClearancesCombustion and Ventilation Air Indoor Units Only Outdoor BoilersHigh-Wind Conditions Outdoor Units Only Outdoor Installations Model VentingModels 181-401 Model Sq. InchesIndoor Installations ModelsIndoor Stack Installation Indoor Installation-ModelIndoor Installation-Models 181-401 Drafthood Installation-Models Vent PipingCommon Venting Vent Damper Installation Models 133 Through 261 Where Required LocationPlumbing Gas Supply ConnectionsVent Damper Normal Operation SummaryVenting of Diaphragm Gas Components Gas Pressure RegulatorGeneral Pump SelectionTemperature & Pressure Gauge Recommended Purge Manifolds forTypical Hydronic System Hookups Feedwater RegulatorSingle Boiler Primary/Secondary Piping-Models Multiple-Boiler- Reverse Return Hook-Up-Models Controls Economaster ControlsElectronic Ignition Operating ControlsMode H2 Motorized Modulation Mode H3 2-Stage FiringMode H4 On/Off Firing Mode H9 4-Stage FiringManual-Reset High Limit Auto-Reset High LimitFlow Switch 100% Pilot SafetyLow Water Cut-Off Optional High and Low Gas Pressure Switches OptionalElectrical Connections START-UP START-UP For Your Safety Read Before Operating For Models with Manual Gas ValvesAfter Start-Up Standing Pilot Checkout Procedure For Models with Automatic Gas ValvesIntermittent Pilot System Checkout S8600 Lighting InstructionsSuggested Inspection Schedule Inspections BurnersControls Blower Adjustment Models 181 toOperation Start-Up S8600HFlame Roll-Out Safety Switch Service Burner Tray RemovalGas Valve Removal Main Burner and Orifice RemovalPilot Removal Combustion Fan RemovalIntermittent Pilot System Honeywell S8600 TroubleshootingElectrical-Electronic Ignition IID Electrical-Standing Pilot Typical ON-OFF Intermittent Ignition Control Wiring Diagram Mechanical Problem Possible Cause Corrective Action Pumps Service Repair Section Tube Cleaning ProcedureBurner Tray Removal Gas Valve RemovalHeat Exchanger Removal Pilot Removal and CleaningHigh Limit or Tankstat Removal Heat Exchanger Re-Assembly Control Well ReplacementTube Replacement Procedure Combustion Chamber RemovalEastman Avenue Oxnard, CA Replacement PartsCleaning Flue Gas Passageways Limited Warranty Raytherm Types H and WH

133-4001 specifications

Raypak 133-4001 is a premier heating solution designed for both residential and commercial applications, known for its efficiency and reliability. This high-performance water heater is specifically engineered to meet the demanding requirements of hot water supply while ensuring energy conservation and user convenience.

One of the standout features of the Raypak 133-4001 is its robust construction. Made from high-quality materials, including a corrosion-resistant heat exchanger and durable casing, this unit is designed to withstand harsh environmental conditions. Its compact design allows for easy installation in various locations, making it an ideal choice for homeowners and businesses alike.

The unit operates on natural gas or LP gas, providing versatility in fuel choice. With a heating capacity of 199,000 BTU/hr, it delivers an impressive flow rate that ensures a steady supply of hot water, even during peak demand periods. This capacity makes it suitable for a wide range of applications, from residential water heating to larger facilities requiring substantial hot water output.

Raypak’s advanced technology set ensures that the 133-4001 operates at maximum efficiency. It utilizes a modulating power burner that adjusts the flame based on demand, optimizing fuel consumption. This feature not only helps in reducing energy bills but also minimizes the carbon footprint, making it an environmentally friendly option.

Another notable characteristic of the Raypak 133-4001 is its digital control system. The intuitive interface allows for precise temperature adjustments and easy monitoring of the heating process. Users can set the desired water temperature, and the system will maintain it consistently, ensuring comfort and reducing the risk of scalding.

Safety is a paramount consideration in the design of the 133-4001. It features a built-in high-limit switch, pressure relief valve, and multiple safety sensors to prevent overheating and potential hazards. These safety features provide peace of mind for homeowners and facility managers, knowing that their hot water system is reliable and secure.

In conclusion, Raypak 133-4001 combines advanced technology, robust construction, and user-friendly features, making it a highly effective water heating solution. Its efficiency and dependability cater to a variety of hot water needs, positioning it as a top choice for both residential and commercial use. Whether for a single-family home or a large facility, the Raypak 133-4001 is built to deliver exceptional performance with every use.
Top Page Image Contents