Home Automation INC. Omni IIe, HOME AUTOMATION owner manual Status, Configuring HLC Devices, Page

Page 43

Status

The Status function is used to display the status of various items in the system. To enter the status menu, from the top-level display or the main menu, press the 6 (STATUS) key on the console keypad.

STATUS

1=CTRL 2=ZONE 3=SUN ↓

4=TEST 5=TEMP 6=ENERGY

↑

1 = CTRL (CONTROL UNITS)

The Control Status menu allows you to view and scroll through the status of each control unit and to configure HLC and UPB devices. To enter the Unit menu, from the Status menu, press the 1 (CTRL) key in the console keypad. The system will display:

DEN LAMP

↓

STATUS OFF

You may enter a unit number to start displaying the status of that unit, or simply press the down arrow key to scroll through the list of units. The status display is as shown under Control, except that now the arrow keys may be used to continue scrolling between units.

Porch Light

00:24:19

LAST COMMANDED

ON

↓

You can also check the state and (if any) the remaining time duration of any Unit.

At this point, you may press the ' # ' key to control the unit as specified under Controlling Units or press ' # # ' to configure and HLC or UPB device.

Note: Only HAI manufactured UPB™ devices (collectively referred to as HLC devices) can be configured using an Omni IIe controller. Other UPB™ devices may be used, but cannot be configured using the Omni IIe controller; they must be configured using a PC running the UPB™ UPStart configuration software.

Configuring HLC Devices

HLC devices can be configured using an Omni console or OmniTouch touchscreen connected to the Omni IIe controller. When configuring HLC devices, the following information is programmed into the HLC device:

¾Network ID (UPB Network ID configured in Omni IIe controller)

¾Network Name (HAI Lighting)

¾Unit ID (Unit Number of respective unit)

¾Unit Name (which is the name description given to the respective unit in the Omni IIe controller)

¾Room Name (using HLC, the name of the first unit in the respective group is used; otherwise the room number is used)

¾Links (every device in each room is programmed with 6 consecutive Links, starting with Link 1; for example, every device in Room 1 is programmed with Links 1-6, Room 2 is programmed with links 7-12, etc.)

¾Other configuration information

When configuring HLC devices using an Omni console or OmniTouch touchscreen, each device (unit number) must first be assigned a name in the Omni IIe controller. HAI recommends that you first configure your Omni IIe controller (naming all of the HLC units) using the HAI PC Access Software, and then download the information to the Omni IIe controller.

Configuring HLC Devices using an Omni Console

To configure HLC devices from an Omni console, use the Status menu. To enter the Status menu, from the top-level display or the main menu, press the 6 (STATUS) key on the console keypad.

STATUS

1=CTRL 2=ZONE 3=SUN ↓

Page 35

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Document Number 20R00-50Rev. January HOME AUTOMATION, INCAll Rights Reserved Copyright 2001-2006Home Automation, IncContents INTRODUCTIONOVERALL DESCRIPTION SECURITY SYSTEM OPERATIONCONTROL TELEPHONE CONTROL PC AccessSETUP APPENDIX A - DIAL OUT PLANNER UNDERWRITERS LABORATORIES REQUIREMENTSFEDERAL COMMUNICATION COMMISSION NOTICE CANADIAN INDUSTRY CANADA NOTICEPage Underwriters Laboratories UL Listing INTRODUCTIONPage 2- DAY OVERALL DESCRIPTIONConsole Operation 1- OFF7- CONSOLE LED Normal Top-LevelDisplayDisplay Menus 6- UP ARROWTo silence the beeper, press the * key Error BeepsMain Menu Trouble BeepsConfirmation Beep Omni IIe MaintenanceCancel Areas1 = DAY SECURITY SYSTEM OPERATIONArming the Security System 0 = OFF4 = VACATION Using Shortcut Keys2 = NIGHT 3 = AWAYRestoring Zones 9 = RESTOREQuick Arm Bypassing Zones#=GOTO What To Do When You Come HomeWhat Happens When the Alarm is Activated Burglar Alarm ActivatedPage Fire Alarm ActivatedGas Alarm Activated Emergency KeysPolice Emergency Duress Code Entered or Duress Alarm ActivatedAlarm Reset Alarm CancelPage Trouble IndicationsCodes Master CodeManager Code Panic SwitchesDuress Code Area ArmingPage GOTO AreaPage Testing Your SystemPage Control CommandsCONTROL About UPBAbout Rooms When set to UPB, the Omni IIe controller canRoom Controller LED Indicators HAI Lighting Control HLC FormatPage About Lutron RadioRAAbout House Controllers About CentraLiteHouse Codes When set to RadioRA, the Omni IIe controller canAbout ALC AboutOmni IIe Unit Numbers Unit NumbersScrolling Through Names Controlling UnitsControlling CentraLite Units Page Configuring Lighting Scenes in an HLC RoomStep OperationControlling ALC or X-10Units Controlling RadioRA UnitsPage Controlling Compose Units Ramp Command ALCPage Internal Flags Timed CommandsScene Command Compose Status of a UnitWHEN ALL ON PHANTOM BUTTON 16 ON Controlling OutputsAll On / Off WHEN ALL ON LINK 50 ON WHEN ALL OFF LINK 50 OFFScene All Lights OnAll Off Leviton Scene ControlScene Off Command Scene CommandsScene Set Command Scene On CommandExecuting CentraLite Scenes Setting a Link Lighting ScenesActivating and Deactivating Links Executing Phantom ButtonsDinner for Two Button ButtonsTemperature Control Leave for Work ButtonPage HAI RC-SeriesThermostatsPage Programmable Energy Saver Modules PESMsPage The following control actions are allowed on PESMsPage Freeze AlarmsIMPORTANT NOTES Indoor and Outdoor TemperaturePage Temperature AlarmsHumidity Temperature Control of AppliancesPage Configuring HLC DevicesConfiguring HLC Devices using an Omni Console StatusStep Operation Setup Mode for HLC DevicesStep Operation Step OperationDEAD - DEAD PHONE LINE ONHK - ON HOOKOFFHK - OFF HOOK RING - RINGINGShow Events Page Event LogShow Message MessagesPage Phone Message Log MessageClear Message Say MessageENTER MESSAGE MSGNAMEPage Remote Phones TELEPHONE CONTROLTelephone Interface In-HousePhonesPage Phone Access Denied - Remote LockoutAlternate Method Main Menu4 - All 1 - Control2 - Security 3 - Button7 - Events When an HAI Communicating Thermostat is enteredWhen a Programmable Energy Saver PESM is entered 6 - StatusPanic Button over the Phone # # # # # # When the HAI Two-WayAudio Module is being used8 - Phone 9 - Good-ByeHow the Omni IIe Voice Dialer Works Emergency Dial-OutDigital Dialer Voice DialerPage What the Omni IIe Voice Dialer DoesWhat You Hear - If Your Omni IIe Calls You Entering the CodeOmni IIe Ethernet Connections PC AccessConnecting to Network via PC Access Built-InEthernet PortController Local NetworkDynamic DNS 192.168.0.101 Hub or HAI Omni IIeRouterPage Local / Wide Area Networki.e i.eAuthority Level SETUPSet Up Codes Access AreasPage Set Up TimeDuress Code TIMEPage Advanced Control Programming ACP1 = Add Programs 2 = Show ProgramsPage Menu3 = Delete All Programs Edit ProgramsPage Times Programs Edit Programs WhenPage Button and Event Programs Control Unit / Switch Press Event ButtonsPage UPB 6-ButtonKeypad Corresponding Switch TableSwitch Omni IIeAll On/Off Event Buttons Zone Event ButtonsPage Page Alarm Event ButtonsUPB Link Event Buttons X-10Event ButtonsMessage Event Buttons Pro-Link Miscellaneous Event ButtonsPage Page Edit Program CommandSwitch Press Event Buttons CentraLite Program Control CommandsWHEN LINK 1 ON Porch Light STATUS Unit Toggle CommandProgram Security Commands WHEN U1 SW UNIT 1 LED 3 ONProgram Temperature Commands Program Button CommandsProgram All On / All Off Commands Program Video CommandsPage Program Message CommandsEdit Program Condition Program Control ConditionsProgram Other Conditions Program Security Mode ConditionsProgram Zone Conditions Program Time Clock ConditionsPage SELECT CONDITION NEVERAnswer Outside Call Set Up DialTelephone Access Remote CommandsPage Dial Out NumberDial Out Numbers Dial OrderAudible Exit Delay Set Up ArmingEntry Delay Exit DelayAll On For Alarm Set up MiscellaneousEnable Quick Arm Enable Auto BypassFORMAT Enable Freeze AlarmFlash For Alarm House Codes 1-4FormatTime Clocks House Codes 1-4All OnPage Page Latitude, Longitude, and Time ZoneZONE NAME Daylight SavingsDESCRIPTION Controller IP AddressController Port Number NUMBEREncryption Key Set Up NamesPage 4=CODE 5=TEMP 6=AREA 8=MSG↑ Set Up VoiceSet Up Address SET UP VOICE 1=CTRL 2=ZONE 3=BTTN ↓FIRE ESCAPE PLANNING UNDERWRITERS LABORATORIES REQUIREMENTSPage Page FEDERAL COMMUNICATION COMMISSION NOTICEIF YOU HAVE TROUBLE WITH YOUR PHONES CANADIAN INDUSTRY CANADA NOTICEPage Omni IIe Voice Dial-OutPlanner APPENDIX A - DIAL OUT PLANNERPage Page INSTRUCTIONS TO CALLED PARTYCODE CHAR APPENDIX B - TEXT DESCRIPTION CHARACTER CODESCODE CHAR CODE CHARCODE APPENDIX C - VOICE DESCRIPTION CODESCODE DESCRIPTIONDESCRIPTION CODEDESCRIPTION CODEDESCRIPTION CODEDESCRIPTION CODEPage CODE DESCRIPTIONCODE DESCRIPTION CODE DESCRIPTIONPage HAI New Orleans, LA U S A NOTE TO INSTALLER
Top Page Image Contents