Home Automation 20A00-1 Burglar Zone Check OUT, Fire Zone Check OUT, Home Control Checkout

Page 32

5.Record the owner's NAME and ADDRESS in the ADDRESS speech memory as shown in SETUP ADDRESS in the OWNER'S MANUAL (Press 8, 9, then 1111 or the current Master code to record the address).

NOTE: DO NOT record any TOUCH TONES in the ADDRESS!!

6.Check that all in-house phones are working.

BURGLAR ZONE CHECK OUT

1.With all doors and windows closed and all motion detectors and security devices secure, the console display should read "SYSTEM OK".

2.If any zones are abnormal, check your wiring. If the battery indication is low, make sure that the battery is connected securely. Give the battery a chance to charge.

3.From the top-level display, have a partner go around the house and trip each sensor one at a time. The display should indicate the correct zone "NOT RDY" when the zone is tripped, then return to "SYSTEM OK" when the zone is secured. Be sure that the zone type indicated (ENTRY/EXIT, PERIMETER, ETC.) is correct for the zone being tested.

4.If the zone being checked is armed, (i.e. PANIC or TAMPER type, which is always armed) the alarm will be activated. Press OFF and 1111 or the current User code to silence the alarm, or bypass the PANIC and TAMPER zone(s) before you start.

5.Reconnect the sirens. Be sure that no one is standing near a siren. Activate the alarm, and ensure that both the inside and, after a delay, outside sirens activate.

FIRE ZONE CHECK OUT

1.Press ' * ' to return the console to the SYSTEM OK indication. Check the fire zone per the sensor manufacturer's instructions. The fire alarm should be activated (pulsing interior sounder, exterior siren).

2.Press ' * ' to silence the alarm. The display will still indicate that the FIRE ZONE is in alarm.

3.Press DAY or NIGHT or AWAY and the User code to arm the system, then OFF and the User code to disarm. This arm/disarm cycle will reset the smoke detector. If the cause for alarm (i.e. smoke) has cleared, the display will return to

SYSTEM OK.

NOTE: Be sure that the DIAL OUT DELAY is long enough so that you can cancel the alarm before the system dials out.

HOME CONTROL CHECKOUT

1.Confirm that the HOUSE CODE on the Omni II is set to the same HOUSE CODE set on all of the modules (See SETUP CONTROL).

2.On the console press 4, 1 (ALL ON). All lamp type modules should go on. Note that some modules, such as appliance modules, voltage outputs, and flags do not respond to ALL ON.

3.On the console press 4, 2 (ALL OFF). All modules should go off. Note that voltage outputs and flags do not respond to ALL OFF.

4.Operate each unit number individually and verify that it works.

5.Ensure that all inputs and outputs are working.

Page 26

Image 32
Contents Installation Manual Page Home Automation, Inc Installation Manual Contents Installer Setup Figures Introduction PlanningInstallation Controller HookupController Hookup About Security Zones Overall Connections Diagram About Fire Zones TWO-WIRE Fire Zone Connections FOUR-WIRE Fire Zone Connections Refer to RJ31X Jack Connections for this configuration Telephone ConnectionsRJ31X Jack Connections Console Setup LCD Console HookupConsole Self Test Console Connections Sounder Outputs Sounder Connections Output Applications Reset OutputsController Outputs Remote ARM/DISARM Switch Home Control ModulesRemote Keyswitch Connections HAI Thermostat Connections HAI ThermostatsProgrammable Energy Saver Modules ConnectionsTemperature / Humidity Sensor Connections TEMPERATURE, Outdoor TEMPERATURE, and HumidityPesm Connections BUILT-IN Serial Port RS-232 Connections Telephone Check OUT System Power UP ProcedureConsole Check OUT Home Control Checkout Burglar Zone Check OUTFire Zone Check OUT Customer Checkout Case of TroubleFollow this procedure for removing the controller board Description of 4/2 Format Digital CommunicatorDescription of Contact ID Format Opening and Closing ReportsHouse Code Installer SetupSetup Control Output Types Output Type Number DescriptionZone Resistors Setup ZonesWireless Receiver Zone Types Type Through Z 48 TypeZone Response Time Zone Type Number DescriptionENTRY/EXIT Latching Zone TypesDescription of Zone Types Police Emergency Duress Emergency Silent Dial OUTSupervised Fire Fire EmergencyKeyswitch Input Outdoor TemperatureTemperature Temperature AlarmSetup Digital Communicator First Phone NUMBER, First Account NumberSecond Phone NUMBER, Second Account Number Communicator TypeReport OPEN/CLOSE Automatic Test TimeSetup Areas Setup Areas ControlSetup Areas Zones Setup Areas ButtonsSET-UP Areas Thermostats Setup Areas ConsolesSetup Areas Messages Thermostat Type Setup TemperaturesTemperature Display Setup Miscellaneous Installer CodeEnable PC Access PC Access CodeOutside Siren Delay Dial OUT DelayAlarm Reset Time Fire Alarm VerificationEnable Emergency Keys Supervise INT SndrSupervise EXT Sndr Time DisplayAC Power Frequency Clock AdjustmentDate Display Dead Line DetectModel and Software Version Reset System EepromReset System RAM Setup Expansion Serial 2 Rate Serial 1 FunctionFunction Types Number Description Omni II Specifications VDCUnderwriters Laboratories UL Installation Requirements Hour Standby Battery Capacity Maximum current ratings for 24-hoursSmoke Detector Installation Guidelines Appendix a Contact ID Reporting Format Zone Type Trip Trouble DescriptionAppendix B Digital Communicator Code Sheet Information for Central StationCode Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Page HAI New Orleans, LA U S a