Home Automation 20A00-1 Police Emergency, Duress Emergency Silent Dial OUT, Supervised Fire, Gas

Page 42

TAMPER ZONES should be used for items such as gun cabinets and liquor closets.

LATCHING TAMPER ZONES ignore the status of that zone during power cycles.

POLICE EMERGENCY

This zone type activates the burglar alarm and sounder. An emergency dial out is activated after the DIAL OUT DELAY.

DURESS EMERGENCY (SILENT DIAL OUT)

If you wish to have a button in your home that activates a SILENT dial out, (no lights flashing and no sounder) it should be connected to a zone that is configured as a DURESS EMERGENCY. If this zone is accidentally tripped, you will not know that the Omni II is making a silent dial out, and hence won't know to stop it.

To stop a silent dial out once it has started, you must go to the console and press OFF then enter your code.

SUPERVISED FIRE

Any zone can be programmed as a SUPERVISED FIRE ZONE. In UL Listed Installations, all fire detectors must be configured as a SUPERVISED FIRE ZONE and connected as shown in this manual. When Zones 1-4 are configured as a SUPERVISED FIRE ZONE, the corresponding Zone Jumpers (JP11-JP14) must be in the "SMK" (smoke) position.

FIRE EMERGENCY

This zone type activates the fire alarm for a normally closed (open for alarm) and open collector (short to ground for alarm) switches. It is not supervised as required for UL Listed Installations and shall NOT be used in such installations.

GAS

This GAS ZONE will generate an alarm, activate the sounder (on - off - on - long off), and make a dial out. This zone type requires an external 1000-ohm end-of-line resistor. When Zones 1-4 are configured as a GAS ZONE, the corresponding Zone Jumpers (JP11-JP14) must be in the "SMK" (smoke) position.

AUXILIARY EMERGENCY

This AUXILIARY EMERGENCY ZONE type will generate an alarm (console beeper - no sirens) and make an emergency dial out when the zone is violated. An emergency dial out is activated after the DIAL OUT DELAY.

TROUBLE

This zone type can be used to monitor the status of an external device, such as the battery status of a wireless security receiver. It can also used to record events in the event log (i.e. driveway activation, opening of a gate, etc.) without setting off the alarm.

When the zone is tripped, the zone name will be displayed on the display as "NOT RDY". The alarm is not activated, regardless of the security mode. The trouble is logged in the event log. The digital communicator (if used) will report the alarm code for the zone. The voice dialer will not be activated.

FREEZE

This FREEZE ALARM ZONE type will generate an alarm (console beeper, no sirens) and make an emergency dial out.

WATER

This WATER ALARM ZONE type will generate an alarm (console beeper, no sirens) and make an emergency dial out.

Page 36

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Installation Manual Page Home Automation, Inc Installation Manual Contents Installer Setup Figures Introduction PlanningInstallation Controller HookupController Hookup About Security Zones Overall Connections Diagram About Fire Zones TWO-WIRE Fire Zone Connections FOUR-WIRE Fire Zone Connections Refer to RJ31X Jack Connections for this configuration Telephone ConnectionsRJ31X Jack Connections Console Setup LCD Console HookupConsole Self Test Console Connections Sounder Outputs Sounder Connections Reset Outputs Controller OutputsOutput Applications Remote ARM/DISARM Switch Home Control ModulesRemote Keyswitch Connections HAI Thermostat Connections HAI ThermostatsProgrammable Energy Saver Modules ConnectionsTemperature / Humidity Sensor Connections TEMPERATURE, Outdoor TEMPERATURE, and HumidityPesm Connections BUILT-IN Serial Port RS-232 Connections System Power UP Procedure Console Check OUTTelephone Check OUT Burglar Zone Check OUT Fire Zone Check OUTHome Control Checkout Customer Checkout Case of TroubleFollow this procedure for removing the controller board Digital Communicator Description of Contact IDDescription of 4/2 Format Format Opening and Closing ReportsInstaller Setup Setup ControlHouse Code Output Types Output Type Number DescriptionSetup Zones Wireless ReceiverZone Resistors Zone Response Time Zone TypesType Through Z 48 Type Zone Type Number DescriptionLatching Zone Types Description of Zone TypesENTRY/EXIT Supervised Fire Police EmergencyDuress Emergency Silent Dial OUT Fire EmergencyTemperature Keyswitch InputOutdoor Temperature Temperature AlarmSecond Phone NUMBER, Second Account Number Setup Digital CommunicatorFirst Phone NUMBER, First Account Number Communicator TypeReport OPEN/CLOSE Automatic Test TimeSetup Areas Setup Areas ControlSetup Areas Zones Setup Areas ButtonsSetup Areas Consoles Setup Areas MessagesSET-UP Areas Thermostats Setup Temperatures Temperature DisplayThermostat Type Enable PC Access Setup MiscellaneousInstaller Code PC Access CodeAlarm Reset Time Outside Siren DelayDial OUT Delay Fire Alarm VerificationSupervise EXT Sndr Enable Emergency KeysSupervise INT Sndr Time DisplayDate Display AC Power FrequencyClock Adjustment Dead Line DetectReset System Eeprom Reset System RAMModel and Software Version Setup Expansion Serial 1 Function Function Types Number DescriptionSerial 2 Rate Omni II Specifications VDCUnderwriters Laboratories UL Installation Requirements Hour Standby Battery Capacity Maximum current ratings for 24-hoursSmoke Detector Installation Guidelines Appendix a Contact ID Reporting Format Zone Type Trip Trouble DescriptionAppendix B Digital Communicator Code Sheet Information for Central StationCode Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Page HAI New Orleans, LA U S a
Top Page Image Contents