Home Automation 20A00-1 installation manual Output Types, Output Type Number Description

Page 38

OUTPUT TYPES

An output type must be specified for each of the voltage outputs and for the interior and exterior horn outputs. The following output types are available:

OUTPUT TYPE		NUMBER	DESCRIPTION
GENERAL PURPOSE		0	General Purpose Output
OK TO ARM		1	OK To Arm
ARMED		2	Armed
PRE-ALM SNDR		3	Pre-Alarm Sounder
INT SNDR		4	Interior Sounder
INT BURG SNDR		5	Interior Burglary Sounder
INT FIRE SNDR		6	Interior Fire Sounder
EXT SNDR		7	Exterior Sounder
EXT BURG SNDR		8	Exterior Burglary Sounder
EXT FIRE SNDR		9	Exterior Fire Sounder
BURG COMM		10	Burglary Communicator
FIRE COMM		11	Fire Communicator
AUX COMM		12	Auxiliary Communicator
SWITCHED POWER		13	Switched Power Output
A1	OK TO ARM	17	Area 1 OK To Arm
A1	ARMED	18	Area 1 Armed
A1	PRE-ALM SNDR	19	Area 1 Pre-Alarm Sounder
A1	INT SNDR	20	Area 1 Interior Sounder
A1	INT BURG SNDR	21	Area 1 Interior Burglary Sounder
A1	INT FIRE SNDR	22	Area 1 Interior Fire Sounder
A1	EXT SNDR	23	Area 1 Exterior Sounder
A1	EXT BURG SNDR	24	Area 1 Exterior Burglary Sounder
A1	EXT FIRE SNDR	25	Area 1 Exterior Fire Sounder
A1	BURG COMM	26	Area 1 Burglary Communicator
A1	FIRE COMM	27	Area 1 Fire Communicator
A1	AUX COMM	28	Area 1 Auxiliary Communicator
A1	SWITCHED POWER	29	Area 1 Switched Power Output

The first group of outputs is global. The sounder and communicator outputs will be activated for an alarm in any area. The remaining types are area specific. Area specific sounder and communicator types will only be activated for alarms in that area. The Setup Control items are:

OUTPUT 1 TYPE:	0
GENERAL PURPOSE #=CHNG ↕
OUTPUT 2 TYPE:	0
GENERAL PURPOSE #=CHNG ↕
OUTPUT 3 TYPE:	0
GENERAL PURPOSE #=CHNG ↕
OUTPUT 4 TYPE:	0
GENERAL PURPOSE #=CHNG ↕
OUTPUT 5 TYPE:	0
GENERAL PURPOSE #=CHNG ↕
OUTPUT 6 TYPE:	0

GENERAL PURPOSE #=CHNG ↕

Page 32

Image 38

Contents Installation Manual Page Home Automation, Inc Installation Manual Contents Installer Setup Figures Introduction PlanningInstallation Controller HookupController Hookup About Security Zones Overall Connections Diagram About Fire Zones TWO-WIRE Fire Zone Connections FOUR-WIRE Fire Zone Connections Refer to RJ31X Jack Connections for this configuration Telephone ConnectionsRJ31X Jack Connections Console Setup LCD Console HookupConsole Self Test Console Connections Sounder Outputs Sounder Connections Output Applications Reset OutputsController Outputs Remote ARM/DISARM Switch Home Control ModulesRemote Keyswitch Connections HAI Thermostat Connections HAI ThermostatsProgrammable Energy Saver Modules ConnectionsTemperature / Humidity Sensor Connections TEMPERATURE, Outdoor TEMPERATURE, and HumidityPesm Connections BUILT-IN Serial Port RS-232 Connections Telephone Check OUT System Power UP ProcedureConsole Check OUT Home Control Checkout Burglar Zone Check OUTFire Zone Check OUT Customer Checkout Case of TroubleFollow this procedure for removing the controller board Description of 4/2 Format Digital CommunicatorDescription of Contact ID Format Opening and Closing ReportsHouse Code Installer SetupSetup Control Output Types Output Type Number DescriptionZone Resistors Setup ZonesWireless Receiver Zone Response Time Zone TypesType Through Z 48 Type Zone Type Number DescriptionENTRY/EXIT Latching Zone TypesDescription of Zone Types Supervised Fire Police EmergencyDuress Emergency Silent Dial OUT Fire EmergencyTemperature Keyswitch InputOutdoor Temperature Temperature AlarmSecond Phone NUMBER, Second Account Number Setup Digital CommunicatorFirst Phone NUMBER, First Account Number Communicator TypeReport OPEN/CLOSE Automatic Test TimeSetup Areas Setup Areas ControlSetup Areas Zones Setup Areas ButtonsSET-UP Areas Thermostats Setup Areas ConsolesSetup Areas Messages Thermostat Type Setup TemperaturesTemperature Display Enable PC Access Setup MiscellaneousInstaller Code PC Access CodeAlarm Reset Time Outside Siren DelayDial OUT Delay Fire Alarm VerificationSupervise EXT Sndr Enable Emergency KeysSupervise INT Sndr Time DisplayDate Display AC Power FrequencyClock Adjustment Dead Line DetectModel and Software Version Reset System EepromReset System RAM Setup Expansion Serial 2 Rate Serial 1 FunctionFunction Types Number Description Omni II Specifications VDCUnderwriters Laboratories UL Installation Requirements Hour Standby Battery Capacity Maximum current ratings for 24-hoursSmoke Detector Installation Guidelines Appendix a Contact ID Reporting Format Zone Type Trip Trouble DescriptionAppendix B Digital Communicator Code Sheet Information for Central StationCode Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Page HAI New Orleans, LA U S a