Home Automation 20A00-1 installation manual Installation, Controller Hookup

Page 8

INSTALLATION

Go over your plan with your customer.

1.Install the entire system. Refer to sections in this manual to see how to install various components.

2.Follow the Power-Up and Checkout procedures.

3.Explain the basics to the customer. Deliver all manuals and documentation.

4.Follow up with your customer to keep them satisfied.

CONTROLLER HOOKUP

1.When choosing a place to mount the controller, consider the following:

a.A duplex outlet, preferably on its own circuit, is required to be within 5 feet of the controller for the power transformer and the X-10 Control Module.

b.The controller should be protected from weather, temperature extremes, and burglars.

2.GROUND THE CONTROLLER "EARTH GND" TERMINAL TO A COLD WATER PIPE OR TO A 4-FOOT GROUND ROD TO PRESERVE ITS BUILT-IN TRANSIENT PROTECTION. USE 14 GAUGE WIRE. TRANSIENT PROTECTION WILL NOT WORK IF THE CONTROLLER IS NOT PROPERLY GROUNDED.

3.Connect the 24 VAC power transformer to the 24 VAC INPUT terminals.

4.Connect the BLACK battery wire to the minus (-) terminal on the battery. DO NOT connect the red wire at this time. DO NOT reverse the connections; the battery fuse will blow. Note that the unit will NOT START on the battery alone.

5.Plug the X-10 Interface Module into the outlet above the transformer. Use the supplied 4-conductor modular telephone cable to connect the module to the jack on the processor board. The red LED on the interface module should be on and will blink off when the interface receives a signal from the controller.

6.Refer to FIGURE 1 (CONTROLLER HOOKUP) for this configuration.

Page 2

Image 8
Contents Installation Manual Page Home Automation, Inc Installation Manual Contents Installer Setup Figures Introduction PlanningInstallation Controller HookupController Hookup About Security Zones Overall Connections Diagram About Fire Zones TWO-WIRE Fire Zone Connections FOUR-WIRE Fire Zone Connections Refer to RJ31X Jack Connections for this configuration Telephone ConnectionsRJ31X Jack Connections Console Setup LCD Console HookupConsole Self Test Console Connections Sounder Outputs Sounder Connections Output Applications Reset OutputsController Outputs Remote ARM/DISARM Switch Home Control ModulesRemote Keyswitch Connections HAI Thermostat Connections HAI ThermostatsProgrammable Energy Saver Modules ConnectionsTemperature / Humidity Sensor Connections TEMPERATURE, Outdoor TEMPERATURE, and HumidityPesm Connections BUILT-IN Serial Port RS-232 Connections Telephone Check OUT System Power UP ProcedureConsole Check OUT Home Control Checkout Burglar Zone Check OUTFire Zone Check OUT Customer Checkout Case of TroubleFollow this procedure for removing the controller board Description of 4/2 Format Digital CommunicatorDescription of Contact ID Format Opening and Closing ReportsHouse Code Installer SetupSetup Control Output Types Output Type Number DescriptionZone Resistors Setup ZonesWireless Receiver Zone Types Type Through Z 48 TypeZone Response Time Zone Type Number DescriptionENTRY/EXIT Latching Zone TypesDescription of Zone Types Police Emergency Duress Emergency Silent Dial OUTSupervised Fire Fire EmergencyKeyswitch Input Outdoor TemperatureTemperature Temperature AlarmSetup Digital Communicator First Phone NUMBER, First Account NumberSecond Phone NUMBER, Second Account Number Communicator TypeReport OPEN/CLOSE Automatic Test TimeSetup Areas Setup Areas ControlSetup Areas Zones Setup Areas ButtonsSET-UP Areas Thermostats Setup Areas ConsolesSetup Areas Messages Thermostat Type Setup TemperaturesTemperature Display Setup Miscellaneous Installer CodeEnable PC Access PC Access CodeOutside Siren Delay Dial OUT DelayAlarm Reset Time Fire Alarm VerificationEnable Emergency Keys Supervise INT SndrSupervise EXT Sndr Time DisplayAC Power Frequency Clock AdjustmentDate Display Dead Line DetectModel and Software Version Reset System EepromReset System RAM Setup Expansion Serial 2 Rate Serial 1 FunctionFunction Types Number Description Omni II Specifications VDCUnderwriters Laboratories UL Installation Requirements Hour Standby Battery Capacity Maximum current ratings for 24-hoursSmoke Detector Installation Guidelines Appendix a Contact ID Reporting Format Zone Type Trip Trouble DescriptionAppendix B Digital Communicator Code Sheet Information for Central StationCode Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Page HAI New Orleans, LA U S a