Hitachi NT50AF, N5009AF manual Methods of Operation

Page 23

English

Do not strike the ram/actuator or any part of the Tool with the metal portion of the mallet. Use the rubber capped end only to

prevent possible injury and/or damage to the Tool.

Do not drive fasteners into thin boards or near corners and edges of work piece. Fasteners can be driven through or away

from work piece and hit someone.

Do not overdrive fasteners. NOFMA states that one reason for

split tongues is overdriving.

Never use Tool which is defective or operating abnormally.

Do not use Tool as a hammer. Disconnect air hose from Tool when:

1)It is not in use;

2)Leaving work area;

3)Moving it to another location; and

4) Handing it to another person.

Wear safety glasses and safety shoes for protection against

foreign objects.

Never use a Hammer with a loose head or splintered handle.

Use only fasteners from Hitachi.

Air supply hoses should have a minimum working pressure rating of 150 psi or 150 percent of the maximum pressure pro-

duced in the power source, whichever is higher.

Check all hoses before connecting to ensure that they are free from dirt, grit, or particles that could alter the performance of

the tool.

An airline Filter and In-Line Air Regulator adjustable to 125 psi

max are required.

NEVER use a defective tool. Replace worn or damaged parts immediately. Be sure that the Safety Trigger and operating mechanisms operate correctly and that all screws and seals are securely tightened at all times.

METHODS OF OPERATION

After connection with power source is made, check to be sure that the airline Regulator pressure is 70-90 psi. Note: Some materials may require a higher pressure in order to countersink the fastener. Harder Material Flooring requires more pressure than typical Oak or Maple. Face Nailing requires approximately 5 psi or more than Angle Nailing.

Ensure that Tool is in proper working order and that there is no leaking of air. If there is an air leak, Disconnect Immediately! Arrange for repairs by a Hitachi authorized service center.

After being sure Tool is operable, place Tool in position to be used. Always place the Tool in proper position against the flooring to be fastened before depressing the trigger and striking the ram.

— 23 —

Image 23
Contents Peligro Manual de instrucciones y seguridadÍndice ContentsTable DES Matieres Definitions of Signal Words Important Safety InformationRead ALL Instructions Important Safety Instructions For Using ToolsNever USE in Presence of Flammable Liquids or Gases Keep Work Area CleanAlways Wear EAR and Head Protection Store Tool ProperlyNever USE NON Relieving Coupler on Tool Check Safety Before USEKeep Visitors Away Dress ProperlyNever Carry Tool by Hose Do not Overreach Check for Live WiresPlace Tool Properly on Work Piece Be Careful of Double Fire DUE to RecoilMaintain Tool with Care Disconnect AIR Hose from Tool WhenStay Alert Handle Tool CorrectlyNever Modify or Alter a Tool EMPLOYER’S ResponsibilitiesNT50AF Name of PartsN5009AF NT50AF SpecificationsFastener Selection Fastener Application Flooring Thickness Fastener Application ChartBefore Operation AccessoriesApplications Filter-Regulator-Lubricator Power SourceAIR Supply Operating Pressure Air HoseHose Coupling Air ConsumptionCold Weather Care LubricationTesting the Tool To Prevent Accidental Injuries Adjusting AIR PressureLoading Fasteners Staple Loading Nail LoadingTool Operation Methods of Operation Do not HIT the Tool Hard Installing Tongue and Groove Flooring English Storing Maintenance and InspectionResetting the Piston / Driver Blade Inspecting the MagazineModifications Maintenance Chart Service and RepairsProblem or Cause Corrective Action Question Operator TroubleshootingEnglish Model NT50AF Exploded View Model NT50AF Parts Listing Model N5009AF Exploded View Model N5009AF Parts Listing Sécurité Définition DES Termes DE SignalisationLire Toutes LES Instructions SécuritéAvertissement Sécurité suiteSE Vêtir DE Façon Appropriée Ranger L’OUTIL DE Façon AppropriéeGarder L’AIRE DE Travail Propre Garder LES Visiteurs À DistancePositionner L’OUTIL Correctement SUR LA Pièce À Fixer Rester SUR SES Gardes 22. Vérifier S’IL Y a DES Fils ÉlectriquesNE Jamais Modifier L’OUTIL Manipuler L’OUTIL DE LA Façon AppropriéeEntretenir L’OUTIL Régulièrement Avertissement Responsabilités DE L’EMPLOYEUR NOM DES Pièces FonctionnementFrançais N5009AF Fiche Technique Choix DES Attaches Attache Utilisation Épaisseur DU Bois Embouveté Tableau de sélection des attachesAvant DE Commencer Accessoires AvertissementUtilisations Filtre-régulateur-lubrificateur Alimentation EN AIRSource d’alimentation Pression de fonctionnement Conduite d’airRaccord de conduite Consommation d’airEssai DE L’OUTIL LubrificationSoins PAR Temps Froid Avertissement Afin DE Prévenir LES Blessures Réglage DE LA Pression D’AIRChargement DES Attaches Chargement DES Broches Chargement DES Clous’outil Fonctionnement DE L’OUTILAu travers du panneau ou dévier et causer une blessure Modes D’UTILISATIONNE PAS Donner DES Coups Puissants SUR L’OUTIL Pose DE Lames DE Bois Embouvetées Français Entreposage Entretien ET InspectionRéenclenchement du piston / de la lame d’entraînement Inspection du chargeurÉtiquette d’avertissement Remarque Service ET Réparation AvertissementAction Raison Marche À Suivre Tableau d’entretienProblème OU Cause Action Correctrice Question DépannageFrançais Français Modèle NT50AF Vue éclatée Modèle NT50AF Liste des pièces Modèle N5009AF Vue éclatée Modèle N5009AF Liste des pièces Nota Informacion Importante DE SeguridadDefiniciones DE LAS Palabras DE Aviso LA MuerteLEA Todas LAS Instrucciones PeligroAdvertencia Nunca LA USE EN Presencia DE Liquidos O Gases IN- Flamables LA Opcion DEL Metodo DE Disparo ES ImportanteGuarde Adecuadamente LA Herramienta Mantenga Limpia EL Area DE TrabajoRevise LA Seguridad Antes DE Usarla Mantenga Alejados a LOS VisitantesUSE Ropa Apropiada No USE Nunca UN Acoplador SIN Descarga EN LA HerramientaRevise Para Detectar Alambres Vivos Coloque LA Herramienta Adecuadamente EN LA Pieza DE TrabajoTenga Cuidado CON LOS Disparos Dobles Debidos AL Retroceso Manipule Correctamente LA Herramienta Desconecte LA Manguera DE Aire DE LA Herramienta CuandoMantengase Alerta Nunca Modifique NI Altere LA Herramienta Manipule LA Herramienta CON CuidadoCuide LA Herramienta Gafas DE Seguridad Advertencia Responsabilidades DEL EmpleadorNombre DE LAS Piezas FuncionamientoDEL Propulsor Especificaciones Seleccion DE Sujetadores Sujetador Aplicacion Grosor DEL Piso DE Tabla para la aplicación de sujetadoresAntes DEL Funcionamiento Accesorios AdvertenciaAplicaciones Fuente de energía Suministro DE AireAcoplador de manguera Filtro-regulador-lubricadorManguera de aire Consumo de aire LubricacionCuidado EN Climas Frios PrecaucionPrueba DE LA Herramienta Para Prevenir Lesiones Accidentales Ajuste DE LA Presion DE AireColocacion DE Sujetadores Colocacion DE Grapas Colocacion DE LOS ClavosFuncionamiento DE LA Herramienta Metodos DE Funcionamiento No Golpee Fuertemente LA Herramienta Instalacion DE Pisos DE Ranura Y Lengüeta Asociación de Fabricantes de Pisos de Arce, Inc Almacenaje Mantenimiento E InspeccionReajuste el pistón/cuchilla propulsora Inspección del cargadorModificaciones Etiqueta de advertenciaServicio Y Reparaciones Advertencia Accion Causa Metodo Tabla para el mantenimientoDetección de averías para el operario Problema O Causa Solucion Pregunta102 103 Modelo NT50AF Despiece Modelo NT50AF Lista de piezas Modelo N5009AF Despiece Modelo N5009AF Lista de piezas Export Blvd. Unit B Mississauga on L5T 2A4 Steve Reynolds Blvd Norcross, GA