Quadra-Fire 5100I-GD-B, 5100I-NL-B warranty Getting Started, Fire Safety, Asphyxiation Risk

Page 5

2

5100-I ACT WOOD INSERT

Getting Started

 

 

 

R

A. Design, Installation & Location Considerations

Consideration must be given to:

Safety

Convenience

Traffic flow

Chimney and chimney connector required

It is a good idea to plan your installation on paper, using exact measurements for clearances and floor protection, before actually beginning the installation.

We recommend that a qualified building inspector and your insurance company representative review your plans before and after installation.

If this appliance is in an area where children may be near it is recommended that you purchase a decorative barrier to go in front of the appliance. Remember to always keep children away while it is operating and do not let anyone operate this appliance unless they are familiar with these operating instructions.

B. Fire Safety

To provide reasonable fire safety, the following should be given serious consideration:

1.Install at least one smoke detector on each floor of your home to ensure your safety. They should be located away from the heating appliance and close to the sleeping areas. Follow the smoke detector manufacturer’s placement and installation instructions, and be sure to maintain regularly.

2.A conveniently located Class A fire extinguisher to contend with small fires resulting from burning embers.

3.A practiced evacuation plan, consisting of at least two escape routes.

4.A plan to deal with a chimney fire as follows: In the event of a chimney fire:

a Evacuate the house immediately b. Notify fire department

CAUTION

Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

WARNING

Fire Risk.

Do not operate appliance before reading and understanding operating instructions.

Failure to operate appliance properly may cause a house fire.

WARNING

Asphyxiation Risk.

Do NOT connect this unit to a chimney flue servicing another appliance.

Do NOT connect to any air distribution duct or system.

May allow flue gases to enter the house.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appli- ance. For assistance or additional information consult a qualified installer, service agency or your dealer.

April 21, 2010

438-0380E

Page

Image 5
Contents Hot glass will cause burns Advanced Combustion Technology ACTSerial Number Location On right side of insert as face the applianceModel Name Manufactured DateTable of Contents Glass Specifications Appliance Certification BTU & Efficiency SpecificationsListing and Code Approvals Mobile Home ApprovedDesign, Installation & Location Considerations Fire SafetyGetting Started Asphyxiation RiskNegative Pressure Inspect Appliance and Components Flue Draft ConsiderationsTools And Supplies Needed Panel Size Dimensions and ClearancesAppliance Dimensions SideWall Clearance to CombustiblesFloor Protection USA & Canada Calculating Alternate Floor Protection MaterialPer Minimum Material Inch Thickness Required Hearth ExtensionHearth Extension Insulation Alternatives, R Value = Outside Air Installation Installation ConsiderationsBlower Cord Location Disconnect the appliance from power supplyOptional Offset Adapter Wiring DiagramVenting Systems Chimney RequirementsInspections Larger ChimneysMasonry Chimney Cont’d Prefabricated Metal Chimney Metal Heat Circulating MasonrySecuring Chimney Components Prefabricated Metal Chimney Cont’dAltering the Fireplace S629M, Standard for 650oC FACTORY-BUILT ChimneysChimney Height / Rise and Run Ovalizing Round Stainless Steel Liners Air ClearancesRule Chimney Termination RequirementsFire Risk Asphyxiation Risk Mobile Home InstallationAppliance Set-up Installation Outline Panel & Trim Set InstallationLeveling Bolts Kit Includes Tools NeededAssembling Trim Securing Liner to Flue CollarIncluded in Kit Tools Needed Zero Clearance Adjustable Trim SupportSize 12 d x 50 w, 2-10 h Over-Firing Your Appliance Operating InstructionsBurning Process Wood Selection & StorageFinal Stage Building a FireSecond Stage BTU / Hr Close Start-Up Air Primary Control Burn Rates & Operating EfficiencyOpacity Primary Air System Air Controls Blower Operating InstructionsStart-up Air System Incorrect Positions Correct Baffle & Blanket PlacementIssues Solutions Frequently Asked QuestionsCreosote Chimney Cleaning General MaintenanceMaintaining & Servicing Your Appliance Disposal of AshesWhen cleaning glass Glass CleaningCleaning Plated Surfaces Quick Reference Maintenance Guide Baffle & Blanket PlacementFrequency As needed Glass Replacement Door AssemblyGlass Replacement Side Window Blower Replacement Door Handle Assembly ReplacementNbr Brick Size Qty Firebrick ReplacementBaffle Removal Start Fire Problems Possible Cause Solution TroubleshootingExploded Drawings Reference MaterialsImportant this is Dated Information HOW to Order Service Parts & AccessoriesDescription Comments Part Number Stocked at Depot HOW to OrderDescription Comments Part Number StockedAt Depot Warranty Policy April 21 438-0380E Do DIS N C OT AR D