Quadra-Fire 5100I-GD-B warranty Air Controls Blower Operating Instructions, Start-up Air System

Page 27

5100-I ACT WOOD INSERT

G. Air Controls

H. Blower Operating Instructions

R

Start-up Air System

The combustion air enters at the rear of the firebox through the rear air tubes. This air supply is controlled by the Start- up Air Control.

Primary Air System

The primary air enters at the upper front of the firebox, near the top of the glass door. This preheated air supplies the necessary fresh oxygen to mix with the unburned gases, helping to create second, third and fourth combustions.

This air is regulated by the Primary Air Control. For more pri- mary air push control “IN”, for less air pull control “OUT”..

This appliance is equipped with a 125° thermally operated snap disc which will automatically turn the blower on when the insert reaches this temperature.

The snap disc is located at the center of the insert, under the lower grille. There is a manual override switch on the right side of the insert. The blower can be controlled manually by switching this switch to ON and operating the blower with the speed control. Figure 27.2.

1.Initial (cold) startup: Leave fan off until your insert is hot and a good coal bed is established, approximately 30 min- utes after fuel is lit.

2.High Burn Setting: The fan may be left on throughout the burn.

P rim ary Air C ontrol

Start-U p Air C ontrol

OPEN - PUSH IN

CLOSE - PULL OUT

Figure 27.1

3.Medium or Medium High Burn Setting: The fan should be left off until a good burn is established, then turned on a medium or high rate.

4.Low Burn Setting: The fan tends to cool the insert. Leave fan off until the burn is well established; then, if you wish, turn the fan on at a low rate.

5.The fan is equipped with a rheostat (speed control). The highest fan speed is obtained by turning the rheostat on, then adjusting back towards “OFF” as far as possible without turn- ing the fan off. For a low fan speed, turn the control knob clockwise as far as possible.

"LOWER 3PEEDE

#ONTROL 2HEOSTAT

3NAPA$ISCS

"Y0ASSS3WITCH

Figure 27.2

April 21, 2010

438-0380E

Page 27

Image 27
Contents Hot glass will cause burns Advanced Combustion Technology ACTManufactured Date Location On right side of insert as face the applianceSerial Number Model NameTable of Contents Mobile Home Approved Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Listing and Code ApprovalsAsphyxiation Risk Fire SafetyDesign, Installation & Location Considerations Getting StartedNegative Pressure Flue Draft Considerations Tools And Supplies NeededInspect Appliance and Components Dimensions and Clearances Appliance DimensionsPanel Size Calculating Alternate Floor Protection Material Clearance to CombustiblesSideWall Floor Protection USA & CanadaHearth Extension Hearth Extension Insulation Alternatives, R Value =Per Minimum Material Inch Thickness Required Outside Air Installation Installation ConsiderationsBlower Cord Location Disconnect the appliance from power supplyOptional Offset Adapter Wiring DiagramLarger Chimneys Chimney RequirementsVenting Systems InspectionsMasonry Chimney Cont’d Prefabricated Metal Chimney Metal Heat Circulating MasonryS629M, Standard for 650oC FACTORY-BUILT Chimneys Prefabricated Metal Chimney Cont’dSecuring Chimney Components Altering the FireplaceChimney Height / Rise and Run Ovalizing Round Stainless Steel Liners Air ClearancesRule Chimney Termination RequirementsFire Risk Asphyxiation Risk Mobile Home InstallationKit Includes Tools Needed Installation Outline Panel & Trim Set InstallationAppliance Set-up Leveling BoltsAssembling Trim Securing Liner to Flue CollarZero Clearance Adjustable Trim Support Size 12 d x 50 w, 2-10 hIncluded in Kit Tools Needed Wood Selection & Storage Operating InstructionsOver-Firing Your Appliance Burning ProcessBuilding a Fire Second StageFinal Stage Burn Rates & Operating Efficiency OpacityBTU / Hr Close Start-Up Air Primary Control Air Controls Blower Operating Instructions Start-up Air SystemPrimary Air System Incorrect Positions Correct Baffle & Blanket PlacementIssues Solutions Frequently Asked QuestionsDisposal of Ashes General MaintenanceCreosote Chimney Cleaning Maintaining & Servicing Your ApplianceGlass Cleaning Cleaning Plated SurfacesWhen cleaning glass Quick Reference Maintenance Guide Baffle & Blanket PlacementGlass Replacement Door Assembly Glass Replacement Side WindowFrequency As needed Blower Replacement Door Handle Assembly ReplacementNbr Brick Size Qty Firebrick ReplacementBaffle Removal Start Fire Problems Possible Cause Solution TroubleshootingExploded Drawings Reference MaterialsImportant this is Dated Information HOW to Order Service Parts & AccessoriesDescription Comments Part Number Stocked at Depot HOW to OrderStocked At DepotDescription Comments Part Number Warranty Policy April 21 438-0380E Do DIS N C OT AR D