Monessen Hearth CR, PF, CL)NVC/PVC manual Main burner switch, Lighting the burner, Pilot position

Page 37

OPERATING INSTRUCTIONS

Designer Series Gas Fireplaces

Lighting burner

main burner switch

The “ON/OFF/RS” switch for the main burner can be found behind door of the fireplace. This switch allows you to turn on and to turn off the main burner without using the gas valve knob. Make sure the button is in the “ON” position to light the main burner. Figure 50

Lighting the burner

Depress and turn the knob counterclockwise to the “ON” position. Figure 51. It will take less than four (4) seconds for the burner to ignite.

Pilot position

Depress and turn knob to pilot position to keep burner off while maintaining the pilot light. Figure 52

			O
		T	N
		T
		O
		L
		I
		P
	Figure 52 -		F
			F
	Pilot Position		O
	Pilot Position	PILOT
		PILOT

to turn off gas

ON	OFF	RS

Figure 50 -

On/Off/RS Switch

N
O		O
		O
		F
		F
		P
PILOT
T	L
O

Figure 51 -

On Position

Depress and turn knob clockwise to “OFF” position. Figure 53

Figure 53 - Off Position

	PI
	L
	O
	T
F
F
O	O
	N
PILOT

42D0200

37

Image 37

Contents Designer Series Direct Vent Gas Fireplace Designer Series Gas Fireplaces Owner InstallerCode Approval Important Safety Information and code approvalPlease Read the Following Carefully Never connect unit to private nonHigh Elevations Product featuresFireplace Dimensions Fireplace Framing Peninsula & Corner Framing SpecificationsPeninsula Framing Framing Fireplace See-through Framing SpecificationsClearances to combustibles ClearancesMantel clearances Finishing MaterialFireplace location Installation and Operating InstructionsSecurE fireplace to floor InstallationOptional top vent application Optional TOP Vent installationInstallation precautions VentING installationVenting Clearances 42D0200 Canadian Installations1 US Installations2 VentING installationGeneral Venting Information Termination Location Dimensions How To Use The Vent GraphFeet Top View Flat Installation Rear Wall Vent installationInstalling Horizontal Vent Cap Adhered to Horizontal termination configurationsExample Horizontal termination configurationBelow Grade Installations Vertical through-the-roof applications Flat ceiling installation Installation for vertical terminationConnect a section of pipe and extend up through the hole Installing gas piping to fireplace / burner system location Fireplace installationInstallation items needed Check gas typePropane/LP Natural GasLabel all wires before disconnecting when Electrical WiringServicing controls. Wiring errors can cause Remote Wall mounted Switch Electrical installationDo not connect wall switch to 110 V circuit Remote Wall Switch Electronic Pilot Ignition WiringOptional DC Remote Systems Glass Frame Removal Glass removalInstall logs and rock wool ember material in firebox LOG PlacementLog placement Install Top Log #6 Log placementVenting Height feet Grille Opening AIR Restrictor AdjustmentInitial lighting What to do if YOU Smell GASNever use an open flame to check for gas leak Never check for gas leak with open Approved leak testing methodFlame Lighting the burner Main burner switchPilot position Cleaning glass Cleaning and maintenanceFirebox cleaning Venting systemStanding Pilot Ignition TroubleshootingElectronic Ignition TroubleshootingYES Glass replacement and blower General troubleshootingOptional Blower accessory Blot Logs Replacement partsDescription Qty Natural Propane Replacement Parts are Available Through Your Retailer Fuel Conversion Kits Millivolt Natural Gas to LP Standing Pilot Millivolt ControlLP to Natural Gas Electronic Ignition Replacement PartsVent Components Replacement PartsDesigner Series Gas Fireplaces Designer Series Gas Fireplaces Designer Series Gas Fireplaces Carbon Monoxide Detector Requirements Five Year Warranty Lifetime WarrantyBasic Warranty If Warranty Service is NeededModel EnerGuide Ratings Fireplace Efficiency % Mhsc