Monessen Hearth KHLDV400, KHLDV500 Safety Features, AUX Control Rear Burner On/Off Control

Figure 61

TOUCH SCREEN REMOTE CONTROL OPERATION KHLDV Series Gas Fireplace

4.After the signal is sent, the On/up and Off/down but- tons become flame height controller again.

5.When the light button is flashing, slide up and down on the arrow buttons will turn the light brightness to HIGH or Off directly without pressing the light button again to confirm

AUX Control (Rear Burner On/Off Control)

The AUX control function is used to turn on or turn off the rear burner connected to the AC module of the Signature Command System. Press the AUX button to turn on or turn off the rear burner.

1.When the rear burner is turned on, the icon will become solid text and the “ON” icon will appear below the “AUX” icon.

2.When the rear burner is turned off, the icon will be- come hollow text and the “ON” icon will disappear.

NOTE: If Smart Mode is entered when rear burner is off, the rear burner will be turned on automatically; when the transmitter is in Smart Mode, AUX button will be disabled. See Smart Mode section for more information.

Setting up Blank Screen or Constant Display in Idle

Figure 61

There is an option to set up how the LCD displays and func- tions when the trans- mitter is in idle. There are two choices:

1.A) Mode. When the transmitter is in idle, the icons in the “touch area”

(timer, thermostat, blower, light and

AUX) will disappear, as shown in the figure on the left. When any of the touch buttons is pressed, those icons will appear and are ready to operate (default).

2.B) Mode. The transmitter always displays all available icons showing current status of timer, thermostat, blower, light and AUX as shown in the figure on the right.

Press TIMER and THERMO buttons at the same time for 3 seconds to toggle between A) and B).

1.When the current setting is A), touch any place in the touch area to bring up the icons then press TIMER but- ton and THERMO button at the same time for 3 sec- onds. The backlight will flash once to indicate that the setting has changed to B).

2.When the current setting is B), pressing TIMER button and THERMO button at the same time for 3 seconds will switch to A) Mode. The touch area icons will disap- pear.

n Safety Features

1.Low Battery Detection

When low battery condition occurs, the transmitter will turn off the fireplace.

A)Battery voltage is checked every one min- ute. When the battery voltage is low, the LCD displays a low battery icon which will exist in all modes.

B)The transmitter will not operate with low battery voltage. Change the batteries before the batteries become too weak for normal operations.

2.Power On Initialization

After the power-on initialization, the transmitter sends a signal to turn off the fireplace.

3.Thermal Shutdown

When the ambient temperature is more than 99°F, the transmitter will turn off the fireplace.

A)The LCD will display “HI”.

B)The Transmitter will not function until the room tem- perature has dropped below 99 degree Fahrenheit.

4.Low Temperature Condition

When the ambient temperature is less than 40 degrees Fahrenheit, the LCD will display “LO”, and NO SIGNAL will be sent to turn on the appliance.

All functions still remain the same for both Manual Mode and Thermostat Mode

5.Child-proof Protection

The child-proof icon will be shown when the child-proof mode is activated by pressing the ON button and the OFF button at the same time for three sec- onds.

A)Enter childproof mode by pressing

and holding both the ON button and the OFF but- ton simultaneously for 3 seconds. The Childproof indicator will be shown on the LCD.

B)Deactivate childproof mode by pressing and hold- ing the ON button and the OFF button simultane- ously for 3 seconds again. The Childproof indicator disappears on the LCD.

C)The transmitter cannot be operated in childproof mode.

73D0024 43