Honeywell Vista-50P/Vista-50PUL manual Programming With #93 Menu Mode, #93 Menu Mode KEY Commands

Page 12

Programming With #93 Menu Mode

NOTE: The following field should be preset before beginning: 2*00 Number of Partitions. In addition, receivers should be programmed via Device programming.

After programming all system related programming fields in the usual way, press #93 while still in programming mode to display the first choice of the menu driven programming functions. Press 0 (NO) or 1 (YES) in response to the displayed menu selection. Pressing 0 will display the next choice in sequence.

#93 MENU MODE KEY COMMANDS

The following is a list of commands used while in the menu mode.

#93	Enters Menu mode
[4]	Serves as ENTER key. Press to have keypad accept entry.

[#]Backs up to previous screen.

0 Press to answer NO

1 Press to answer YES

01-09 All data entries are either 1-digit or 2-digit entries.

00 Exits menu mode, back into field programming mode, when entered at the first question for each category.

Menu selections are as follows:

PROMPTEXPLANATION

ZONE PROG?
1 = YES 0 = NO	0

For programming the following:

•Zone Number

•Zone Response Type

•Partition Number for Zone

•Dialer report code for zone

•Input Device Type for zone (whether RF, polling loop, etc.)

•Enrolling serial numbers of 5800 Series transmitters & serial polling loop devices into the system.

	EXPERT MODE?
	1 = YES	0 = NO	0



	ALPHA PROG?
	1 = YES	0 = NO	0

Same as Zone Programming except:

•Done with a minimum number of keystrokes.

•Can program wireless keys using pre-defined templates.

For entering alpha descriptors for the following:

•Zone Descriptors

•Installer's Message

•Custom Words

•Partition Descriptors

•Relay Descriptors

DEVICE PROG?
1 = YES 0 = NO	0

For defining the following device characteristics for addressable devices, including keypads, RF receivers (5881), output relay modules (4204), and 4285/4286 VIP Module:

•Device Address

•Device Type

•Keypad Options (incl. partition assignment)

•RF House ID

	RELAY PGM?
	1 = YES	0 = NO	0



	RLY VOICE DESCR?
	1 = YES	0 = NO	0



	CUSTOM INDEX ?
	1 = YES	0 = NO	0

For defining output relay functions.

For entering voice descriptors for relays to be used with the 4285/4286 VIP Module.

For creating custom word substitutes for VIP Module annunciation.

– 12 –

Image 12

Contents $0&29,67$65,6 9,67$39,67$38 VISTA50P-PRV2 5/04 Rev aTable of Contents Recommended Programming Procedure Program Field Index Field GroupField Group VISTA-50P/VISTA-50PUL Programming Form Enable OPEN/CLOSE Report for OPEN/CLOSE Report for Keyswitch59 *62 Alarm Report Codes & ID Digits for Zones 64 *67 Alarm Report Codes & ID Digits for ZonesFields 1*28 1*31 are not applicable for UL installations 2nd Page Programming Fields press *943rd Page Programming Fields press *94 Summary of Programming Commands Partition-Specific Fields 1st Page Fields2nd Page Programming Fields press *94 Enable J7 Triggers by Partition Programming With #93 Menu Mode #93 Menu Mode KEY CommandsZone Programming SET to CONFIRM?Enter Zone no Zone Type PERIMETER03Input Type Input S/N AXXX-XXXXInput S/N Series Transmitters Loop Designations Xmit to Confirm Press to SkipExpert Mode Zone Programming Program field 200 Number of PartitionsInput S/N XXX-XXXX On this screenEntering Wireless Keys From TemplatePartition Enter Zone no Wireless Key Default Templates 5804 5804BDTemplate Loop Function Zone Type Template Loop FunctionZone Descriptors Select Zone Descriptor mode Alpha Descriptors ProgrammingSelect Default Screen mode Select Custom Word ModeAccept the word Select the next wordType the word using one of two methods as follows Follow the same procedure as for custom wordsEnter the custom word number 01-20 you want to create Save the word by pressingAlpha Descriptor Vocabulary See the Relay Voice Descriptors section whenDevice Programming Alpha or Fixed-Word KeypadRF Expander VIP ModuleAlarm FaultRelay Programming TroubleRelay Devices Programming Choices for Start/Stop Zone Types and System OperationsEnter Relay # Relay Action No Response Start Event Not UsedStart Partn ANY Partition Relay Type ECP ECP Address Module RELAY# House CodeUnit Code Relay Voice Descriptors Zone List ProgrammingWord Index Custom Word Substitutes for VIP Module Annunciation Custom Word no =QUIT Enter Index #System Layout Worksheets PartitionsCommunication Options by Partition System Definitions by Partition enter values or yes/noAccess Codes & User Definitions for Partitions 1 Printer OptionsEvent LOG Types Devices keypads, 4204, rf receivers, vip moduleAccess Codes & User Definitions for Partitions 3 Access Codes & User Definitions for Partitions 5Access Codes & User Definitions for Partitions 7 Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Definitions for System Zones 88 89, 90, 91, 97 Zone TypesInput Types ZoneRelay Devices Worksheets Applicable only if relays 4204, or X-10 devices are usedDevice Action EventZT = Zone TYPE/SYSTEM Operation = Partition No -8, 0 = Any#80 & #81 Menu Mode KEY Commands Scheduling Menu PromptsScheduling Worksheets Start TimeStop Time Time Window NumberHOL Month/Day PartitionSched Num Time Window Days W T F S S HRelay commands Arm/Disarm commandsBypass commands Open/Close WindowsPartition/Windows Disarm Window HhmmArm Window Mon Tue Wed Thu Fri Sat SunPartition/Windows Disarm Window Ademco VISTA-50P/VISTA-50PUL Summary of Connections Eileen Way, Syosset, New York VISTA50P-PRV2 5/04 Rev. a