Honeywell Vista-50P/Vista-50PUL manual Device Programming, Alpha or Fixed-Word Keypad, RF Expander

Page 24

Device Programming

This menu is used to program keypads, receivers, and relay modules, etc.

Device Address 00 is always set as an alpha keypad assigned to Partition 1 with no sounder suppression options, and these settings cannot be changed.

From Data Field Programming mode, press #93 to display "ZONE PROG?" Press [0] repeatedly to display "DEVICE PROG?"

PROMPTEXPLANATION

 

DEVICE PROG?

 

 

1=YES 0=NO

0

 

 

 

 

 

 

 

 

DEVICE ADDRESS

 

 

01-30, 00=QUIT

01

 

Press [1] to enter Device Programming.

The device address identifies the device to the control. Enter the 2-digit device address number to match the device’s physical address setting (01-30).

Press [✱] to accept entry.

DEVICE TYPE

Select the type of addressable device as follows:

 

00

00

= device not used

 

01

= alpha keypad (6139/6160)

 

02

= fixed-word keypad (6137/6150)

Press [✱] to accept entry.

Alpha or Fixed-Word Keypad

03 = RF receiver (5881)

04 = output relay module (4204)

05 = voice (VIP) Module (4285/4286)

PROMPTEXPLANATION

01 CONSOLE PART.

1

If you selected device type 01 (alpha keypad), or 02 (fixed-word keypad), this prompt appears. Enter the addressable device’s default partition number (01 to maximum number of partitions programmed for system in field 2*00). This is the primary partition for the device. Enter 9 to make this keypad a "Master" keypad for the system.

Press [✱] to accept entry.

01 SOUND OPTION

00

Keypads can be individually programmed to suppress arm/disarm beeps, entry/exit beeps and chime mode beeps. This helps prevent unwanted sounds from disturbing users in other areas of the premises.

Enter a number 00-03for the keypad sounding suppression options desired for the keypad as follows: 00 = no suppression

01 = suppress arm/disarm & entry/exit beeps

02 = suppress chime mode beeps only

03 = suppress arm/disarm, entry/exit and chime mode beeps Press [✱] to accept entry.

RF Expander

PROMPTEXPLANATION

01 RF EXPANDER

 

HOUSE I

00

If you selected device type 03 (RF receiver), this prompt appears. Enter the 2-digit House ID (00-31). This is required if you are using a wireless keypad (5827/5827BD).

Press [✱] to accept entry.

VIP Module

PROMPTEXPLANATION

01 MODULE PART.

1

If you selected device type 05 (VIP Module) this prompt appears. Enter the partition number 1-8in which the module is located.

Press [✱] to accept entry.

Press 00 + [✱] to exit Menu mode. Press ✱99 to exit Program mode.

– 24 –

Page 23 Page 25
Image 24
Page 23 Page 25
Contents $0&29,67$65,6 9,67$39,67$38 VISTA50P-PRV2 5/04 Rev aTable of Contents Recommended Programming Procedure Program Field Index Field GroupField Group VISTA-50P/VISTA-50PUL Programming Form Enable OPEN/CLOSE Report for OPEN/CLOSE Report for Keyswitch59 *62 Alarm Report Codes & ID Digits for Zones 64 *67 Alarm Report Codes & ID Digits for ZonesFields 1*28 1*31 are not applicable for UL installations 2nd Page Programming Fields press *943rd Page Programming Fields press *94 Summary of Programming Commands Partition-Specific Fields 1st Page Fields2nd Page Programming Fields press *94 Enable J7 Triggers by Partition Programming With #93 Menu Mode #93 Menu Mode KEY CommandsZone Programming SET to CONFIRM?Enter Zone no Zone Type PERIMETER03Input Type Input S/N AXXX-XXXXInput S/N Series Transmitters Loop Designations Xmit to Confirm Press to SkipExpert Mode Zone Programming Program field 200 Number of PartitionsInput S/N XXX-XXXX On this screenEntering Wireless Keys From TemplatePartition Enter Zone no Wireless Key Default Templates 5804 5804BDTemplate Loop Function Zone Type Template Loop FunctionZone Descriptors Select Zone Descriptor mode Alpha Descriptors ProgrammingSelect Default Screen mode Select Custom Word ModeAccept the word Select the next wordType the word using one of two methods as follows Follow the same procedure as for custom wordsEnter the custom word number 01-20 you want to create Save the word by pressingAlpha Descriptor Vocabulary See the Relay Voice Descriptors section whenDevice Programming Alpha or Fixed-Word KeypadRF Expander VIP ModuleAlarm FaultRelay Programming TroubleRelay Devices Programming Choices for Start/Stop Zone Types and System OperationsEnter Relay # Relay Action No Response Start Event Not UsedStart Partn ANY Partition Relay Type ECP ECP Address Module RELAY# House CodeUnit Code Relay Voice Descriptors Zone List ProgrammingWord Index Custom Word Substitutes for VIP Module Annunciation Custom Word no =QUIT Enter Index #System Layout Worksheets PartitionsCommunication Options by Partition System Definitions by Partition enter values or yes/noAccess Codes & User Definitions for Partitions 1 Printer OptionsEvent LOG Types Devices keypads, 4204, rf receivers, vip moduleAccess Codes & User Definitions for Partitions 3 Access Codes & User Definitions for Partitions 5Access Codes & User Definitions for Partitions 7 Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Definitions for System Zones 88 89, 90, 91, 97 Zone TypesInput Types ZoneRelay Devices Worksheets Applicable only if relays 4204, or X-10 devices are usedDevice Action EventZT = Zone TYPE/SYSTEM Operation = Partition No -8, 0 = Any#80 & #81 Menu Mode KEY Commands Scheduling Menu PromptsScheduling Worksheets Start TimeStop Time Time Window NumberHOL Month/Day PartitionSched Num Time Window Days W T F S S HRelay commands Arm/Disarm commandsBypass commands Open/Close WindowsPartition/Windows Disarm Window HhmmArm Window Mon Tue Wed Thu Fri Sat SunPartition/Windows Disarm Window Ademco VISTA-50P/VISTA-50PUL Summary of Connections Eileen Way, Syosset, New York VISTA50P-PRV2 5/04 Rev. a
Top Page Image Contents