Honeywell Vista-50P/Vista-50PUL manual Table of Contents

Page 2

Table of Contents

Recommended Programming Procedure

3

Relay Programming

25

Program Field Index

4

Relay Voice Descriptors

28

VISTA-50P/VISTA-50PUL Programming Form

5

Relay Voice Descriptors and Custom Word

 

Partition-Specific Fields

10

Substitutes Vocabulary

29

Custom Word Substitutes for VIP Module

 

Programming With #93 Menu Mode

12

 

Annunciation

30

Zone Programming

13

System Layout Worksheets

31

5800 Series Transmitters Loop Designations

15

Relay Devices Worksheets

39

Expert Mode Zone Programming

16

Scheduling Menu Prompts

41

Alpha Descriptors Programming

20

Scheduling Worksheets

42

Alpha Descriptor Vocabulary

23

VISTA-50P/VISTA-50PUL Summary of

 

Device Programming

24

 

Connections Diagram

47

 

 

The purpose of this document is to provide a quick and easy way to program your entire system. A recommended programming procedure is included, followed by a list of program fields with the corresponding program group they belong to (system-wide, partition-specific, scheduling, etc.). Two program forms are included. One contains all the programming fields, and the other contains the partition-specific fields. If you are setting up a single-partition system, the partition-specific fields become system-wide fields.

Following the program forms are system layout worksheets. We recommend that you use these sheets to plan your system before programming is performed. If you need further information about specific programming options, see the ADEMCO VISTA-50P/VISTA-50PUL Installation and Setup Guide.

Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."

Single-Partition System

The system default is for a single-partition system. Use the VISTA-50P/VISTA-50PUL SINGLE PARTITION PROGRAMMING FORM when programming for single-partition usage. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure.

Multiple-Partition System

You must enter the number of partitions you are using in data field 2*00 to set the system for multiple partitions. Use the VISTA-50P/VISTA-50PUL SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM FORMS when programming the system for multiple partitions. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure.

SUMMARY OF PROGRAMMING COMMANDS

•To enter program mode, enter installer code + [8] + [0] + [0]

•To set standard defaults, press ✱97

•To change to next page of program fields, press ✱94

•To return to previous set of fields, press ✱99

•To erase account and phone number field entries, press [✱] + field number + [✱]

•To assign zone descriptors, press #93 + follow menu prompts

•To add custom words, press #93 + follow menu prompts

•To enter Installer's Message, press #93 + follow menu prompts

•To exit program mode, enter ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code. ✱98 prevents re-access to programming mode by installer code.

Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.

– 2 –

Page 1 Page 3
Image 2
Page 1 Page 3
Contents $0&29,67$65,6 9,67$39,67$38 VISTA50P-PRV2 5/04 Rev aTable of Contents Recommended Programming Procedure Field Group Program Field IndexField Group VISTA-50P/VISTA-50PUL Programming Form 59 *62 Alarm Report Codes & ID Digits for Zones Enable OPEN/CLOSE Report forOPEN/CLOSE Report for Keyswitch 64 *67 Alarm Report Codes & ID Digits for ZonesFields 1*28 1*31 are not applicable for UL installations 2nd Page Programming Fields press *943rd Page Programming Fields press *94 Summary of Programming Commands 2nd Page Programming Fields press *94 Partition-Specific Fields1st Page Fields Enable J7 Triggers by Partition Programming With #93 Menu Mode #93 Menu Mode KEY CommandsEnter Zone no Zone ProgrammingSET to CONFIRM? Zone Type PERIMETER03Input S/N Input TypeInput S/N AXXX-XXXX Series Transmitters Loop Designations Xmit to Confirm Press to SkipExpert Mode Zone Programming Program field 200 Number of PartitionsInput S/N XXX-XXXX On this screenPartition Enter Zone no Entering Wireless KeysFrom Template Template Loop Function Wireless Key Default Templates 58045804BD Zone Type Template Loop FunctionZone Descriptors Select Zone Descriptor mode Alpha Descriptors ProgrammingAccept the word Select Default Screen modeSelect Custom Word Mode Select the next wordEnter the custom word number 01-20 you want to create Type the word using one of two methods as followsFollow the same procedure as for custom words Save the word by pressingAlpha Descriptor Vocabulary See the Relay Voice Descriptors section whenRF Expander Device ProgrammingAlpha or Fixed-Word Keypad VIP ModuleRelay Programming AlarmFault TroubleEnter Relay # Relay Devices ProgrammingChoices for Start/Stop Zone Types and System Operations Relay Action No Response Start Event Not UsedUnit Code Start Partn ANY PartitionRelay Type ECP ECP Address Module RELAY# House Code Relay Voice Descriptors Zone List ProgrammingWord Index Custom Word Substitutes for VIP Module Annunciation Custom Word no =QUIT Enter Index #Communication Options by Partition System Layout WorksheetsPartitions System Definitions by Partition enter values or yes/noEvent LOG Types Access Codes & User Definitions for Partitions 1Printer Options Devices keypads, 4204, rf receivers, vip moduleAccess Codes & User Definitions for Partitions 7 Access Codes & User Definitions for Partitions 3Access Codes & User Definitions for Partitions 5 Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Input Types Zone Definitions for System Zones 88 89, 90, 91, 97Zone Types ZoneDevice Action Relay Devices WorksheetsApplicable only if relays 4204, or X-10 devices are used EventZT = Zone TYPE/SYSTEM Operation = Partition No -8, 0 = Any#80 & #81 Menu Mode KEY Commands Scheduling Menu PromptsStop Time Scheduling WorksheetsStart Time Time Window NumberSched Num Time Window Days HOLMonth/Day Partition W T F S S HBypass commands Relay commandsArm/Disarm commands Open/Close WindowsArm Window Partition/Windows Disarm WindowHhmm Mon Tue Wed Thu Fri Sat SunPartition/Windows Disarm Window Ademco VISTA-50P/VISTA-50PUL Summary of Connections Eileen Way, Syosset, New York VISTA50P-PRV2 5/04 Rev. a
Top Page Image Contents