Honeywell Vista-50P/Vista-50PUL manual Expert Mode Zone Programming

Page 16

PROMPTEXPLANATION

ENTER ZONE NO.
00 = QUIT	11

The system now returns to the “ENTER ZONE NO.” prompt for the next zone. When all zones have been programmed, enter “00” to quit.

After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information (zone number, zone type, etc.) relevant to that device.

When you have finished programming all zones, test each using the system’s Test Mode. Do not use the Transmitter ID Sniffer Mode. The system checks only for transmission of one zone on a particular transmitter, NOT the zones assigned to each additional loop, and also does not verify polling loop type zones.

Expert Mode Zone Programming

Expert mode allows you to program zones using the minimum number of screens and keystrokes.

Expert Mode Zone Programming does not provide the capability to program some of the zone’s attributes, such as Arm w/Fault, Vent Zone, STAY mode, Auto-STAY, Bypass Group, etc. If you want to program a zone for any of these attributes, you must use Zone Programming.

Enter the Programming mode with [Installer Code] + 8 0 0

Before programming your zones, do the following:

1.Program field 2✱00: Number of Partitions.

2.Enable your RF Receiver in Device Programming menu mode.

To program your zones, press ✱93 to display the "ZONE PROG?" prompt. Enter “0” (NO) to each prompt until the “EXPERT MODE?” prompt appears.

PROMPTEXPLANATION

	EXPERT MODE?
	1 = YES		0 = NO			0
	1 = YES		0 = NO			0


	SET TO CONFIRM?
	0 = NO		1 = YES			0
	0 = NO		1 = YES			0


	Zn	ZT	P RC		In	L
	01	03 1 10 HW				-
	01	03 1 10 HW				-


	Zn	ZT	P	RC	In	L
	10	03	1	10	RF	1s
	10	03	1	10	RF	1s

Press 1 to enter Expert mode.

This prompt appears once upon entering Expert Mode.

If you select “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have been entered later.

A summary display appears, showing zone 1’s current programming or default values.

Enter the desired 2-digit zone number and press [✱]. Note: If you want to exit the Expert mode, enter “00” + [✱].

If an “s” appears after the loop number, it indicates that the transmitter’s serial number has been enrolled. Use the [D] key to enter and duplicate wireless keys (see “Entering Wireless Keys” later)

– 16 –

Image 16

Contents $0&29,67$65,6 9,67$39,67$38 VISTA50P-PRV2 5/04 Rev aTable of Contents Recommended Programming Procedure Field Group Program Field IndexField Group VISTA-50P/VISTA-50PUL Programming Form Enable OPEN/CLOSE Report for OPEN/CLOSE Report for Keyswitch59 *62 Alarm Report Codes & ID Digits for Zones 64 *67 Alarm Report Codes & ID Digits for ZonesFields 1*28 1*31 are not applicable for UL installations 2nd Page Programming Fields press *943rd Page Programming Fields press *94 Summary of Programming Commands 1st Page Fields Partition-Specific Fields2nd Page Programming Fields press *94 Enable J7 Triggers by Partition Programming With #93 Menu Mode #93 Menu Mode KEY CommandsZone Programming SET to CONFIRM?Enter Zone no Zone Type PERIMETER03Input S/N AXXX-XXXX Input TypeInput S/N Series Transmitters Loop Designations Xmit to Confirm Press to SkipExpert Mode Zone Programming Program field 200 Number of PartitionsInput S/N XXX-XXXX On this screenFrom Template Entering Wireless KeysPartition Enter Zone no Wireless Key Default Templates 5804 5804BDTemplate Loop Function Zone Type Template Loop FunctionZone Descriptors Select Zone Descriptor mode Alpha Descriptors ProgrammingSelect Default Screen mode Select Custom Word ModeAccept the word Select the next wordType the word using one of two methods as follows Follow the same procedure as for custom wordsEnter the custom word number 01-20 you want to create Save the word by pressingAlpha Descriptor Vocabulary See the Relay Voice Descriptors section whenDevice Programming Alpha or Fixed-Word KeypadRF Expander VIP ModuleAlarm FaultRelay Programming TroubleRelay Devices Programming Choices for Start/Stop Zone Types and System OperationsEnter Relay # Relay Action No Response Start Event Not UsedRelay Type ECP ECP Address Module RELAY# House Code Start Partn ANY PartitionUnit Code Relay Voice Descriptors Zone List ProgrammingWord Index Custom Word Substitutes for VIP Module Annunciation Custom Word no =QUIT Enter Index #System Layout Worksheets PartitionsCommunication Options by Partition System Definitions by Partition enter values or yes/noAccess Codes & User Definitions for Partitions 1 Printer OptionsEvent LOG Types Devices keypads, 4204, rf receivers, vip moduleAccess Codes & User Definitions for Partitions 5 Access Codes & User Definitions for Partitions 3Access Codes & User Definitions for Partitions 7 Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Definitions for System Zones 88 89, 90, 91, 97 Zone TypesInput Types ZoneRelay Devices Worksheets Applicable only if relays 4204, or X-10 devices are usedDevice Action EventZT = Zone TYPE/SYSTEM Operation = Partition No -8, 0 = Any#80 & #81 Menu Mode KEY Commands Scheduling Menu PromptsScheduling Worksheets Start TimeStop Time Time Window NumberHOL Month/Day PartitionSched Num Time Window Days W T F S S HRelay commands Arm/Disarm commandsBypass commands Open/Close WindowsPartition/Windows Disarm Window HhmmArm Window Mon Tue Wed Thu Fri Sat SunPartition/Windows Disarm Window Ademco VISTA-50P/VISTA-50PUL Summary of Connections Eileen Way, Syosset, New York VISTA50P-PRV2 5/04 Rev. a