Bosch Appliances D7212G manual Related Documentation, Documentation Conventions

Page 10

D7212G

Introduction

1.2Related Documentation

Table 2 is a comprehensive list of all documentation (with part numbers) directly related to the D7212G Control/ Communicator. Throughout this guide, references are made to this documentation. If you need one or more of these documents, please contact Bosch Security Systems Technical Support and request the documentation by part number.

Name of Document	Part Number
D1255 Installation Instructions	74-06819-000
D1256/D1257 Installation Instructions	74-06925-000
D1260 Installation Guide	48101
D5200 Operation Manual	74-06176-000

D720 Installation Instructions	74-06918-000
D7212G Approved Applications Compliance Guide	4998138560

D7212G Operation and Installation Guide (this document)	4998138544
D7212G Program Entry Guide	4998138538
D7212G Program Record Sheet	4998138542
D7212G Release Notes	4998138543

D8125MUX Operation and Installation Guide	36796
D9412G/D7412G/D7212G Installation and Troubleshooting Quick Reference Guide	43700

RAM IV Operations Manual	38849
Security System Owner’s Manual	71-06633-000

Security System Owner’s Manual Supplement	33267
7000/9000 Series Point Chart Label	79-06660-000

9000/9000G Series Technogram: UL Certificated Bank Safe and Vault Applications	73-07302-000
9000/9000G Series Technogram: Smoke Detector Compatibility	33284

Table 2: Related Documentation

1.3Documentation Conventions

1.3.1Type Styles Used in the Text

Special type styles are used to help identify the objects being described in this guide.

Bold Text

Bold Italicized Text

Italicized Text

Courier New Text

[CAPITALIZED TEXT]

Usually indicates selections that you may use while programming your panel. May also indicate an important fact that should be noted.

Denotes notes, cautions and/or warnings.

Refers you to a drawing, table, or other section of this document, or to another document. Also used to symbolize names for records that you will create.

Indicates what may appear on the D5200 Programmer display, command center/keypad or internal printer.

Indicates a specific key to be pressed.

D7212G Operation and Installation Guide

4998138544C

Page 10

© 2003 Bosch Security Systems

Image 10

Contents Control/Communicator D7212G Operation and Installation Guide D7212GContents 11.1 10.111.2 10.0 11.013.0 Figures D7212G Operation and Installation Guide Organization TablesSection Description IntroductionGuide Organization Appendix DescriptionDocumentation Conventions Related DocumentationType Styles Used in the Text Tips, Notes, Cautions and Warnings FCC RulesPart D7212G Overview New Features D9412G D7412G D7212G9000G Series Panel Differences Specifications SecondaryTelephone Connections Telephone Line Ground Fault Detect Features in D7212GCompatible Accessories IntroductionStandard Features Model Display Application Control/Communicator Assembly Other FeaturesComponents and Literature Available by Separate Order Burglary Listings and ApprovalsListings Before Beginning InstallationBeginning the Installation Enclosure OptionsGround Fault Detect Enable Installing the AssemblyConnecting Earth Ground Locking the Reset PinInstall and Wire Detection Devices Finishing the InstallationCharge the Battery While Finishing Install Modules and RelaysTesting the System Install the Point Chart LabelProgramming the Panel Primary Power Terminals Power SupplySecondary Power Terminals Installing the Battery Replacing the BatteryBattery Discharge/Recharge Schedule Battery SupervisionBattery Charging Circuit Float Charge Discharge CycleAction Charging Status and Low Battery LEDsType Color StateAux Power Terminals Continuous Current Draw Power OutputsTotal Available Power Programmable Power Outputs TerminalsFire System Power Formula Relay InstallationAvailable Power Verification/Reset RelayTelephone Connections Phone Line Monitor Operation Monitor LED GreenDialing Format Called Party DisconnectLoop Start Ground StartPhone Monitor Select Jumper Position Ground StartD7212G Point Sensor Loops On-board PointsDescription Terminals Point ParametersBell Off-board Points Point Zonex Bus D7212G TerminalsInstalling the D8125 Popex Module D8125, D8127 and D9127 Popit ModulesLength in ft. m Wiring Data Expansion Loops to Popex ModulesExpansion Loops Combined Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Program Record Sheet Popit Module Point AssignmentsRadxpnts Handler Popit Labels Installing the OctoPOPITD8128D OctoPOPIT Module DescriptionWiring OctoPOPITs Line TerminationD8128D Address Switches Testing Off-board PointsAddress Assignment Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G Off-board Relays Panel Relay D8129 OctoRelay D8129 OctoRelay Switch NumberD8129 OctoRelay D8129 Connections to the D7212G Address Switch Command Center TerminalsAssigning the command center an address Arming DevicesD7212G Command Center Terminal Function Power at Command Centers10.3 D279A Independent Zone Control KeyswitchKeyswitch Operation Maintained Contact Momentary ContactD7212G SDI Devices InstallationPrinter Switch 11.3 D9131A Parallel Printer Interface ModuleSDI Address Address Settings 11.5.2 D9133TTL-E Network Interface ModuleD7212G Accessory Connector Programmer and Accessory ConnectionsProgrammer Connector Programmer Access ReportsAccessoryProgramming ConnectorConnector Programmer and Accessory ConnectionsFaceplate 13.0 13.1 D7212G FaceplateFaceplate Appendix a System Wiring Diagrams, Issue a D7212G Control/Communicator, 1D7212G System Wiring Diagram, 2 D7212G Control/Communicator, 2D7212G System Wiring Diagram, 3 D7212G Control/Communicator, 3D7212G Appendix B Point Address Chart Zonex 1, Points 9 toD7212G Symbols IndexZonex