Bosch Appliances manual Faceplate 13.0, 13.1 D7212G Faceplate

Page 59

D7212G

Faceplate

13.0	Faceplate
13.1	D7212G Faceplate

Figure 21: D7212G Faceplate

D7212G Operation and Installation Guide

Page 59

4998138544C

Image 59

Contents Control/Communicator D7212G D7212G Operation and Installation GuideContents 11.2 10.111.1 11.0 10.013.0 Figures Tables D7212G Operation and Installation Guide OrganizationAppendix Description IntroductionGuide Organization Section DescriptionType Styles Used in the Text Related DocumentationDocumentation Conventions Part FCC RulesTips, Notes, Cautions and Warnings D7212G 9000G Series Panel Differences New Features D9412G D7412G D7212GOverview Secondary SpecificationsTelephone Connections Telephone Line Introduction Features in D7212GCompatible Accessories Ground Fault DetectStandard Features Model Display Application Components and Literature Available by Separate Order Other FeaturesControl/Communicator Assembly Listings Listings and ApprovalsBurglary Enclosure Options InstallationBeginning the Installation Before BeginningLocking the Reset Pin Installing the AssemblyConnecting Earth Ground Ground Fault Detect EnableInstall Modules and Relays Finishing the InstallationCharge the Battery While Finishing Install and Wire Detection DevicesProgramming the Panel Install the Point Chart LabelTesting the System Secondary Power Terminals Power SupplyPrimary Power Terminals Replacing the Battery Installing the BatteryDischarge Cycle Battery SupervisionBattery Charging Circuit Float Charge Battery Discharge/Recharge ScheduleColor State Charging Status and Low Battery LEDsType ActionProgrammable Power Outputs Terminals Power OutputsTotal Available Power Aux Power Terminals Continuous Current DrawVerification/Reset Relay Relay InstallationAvailable Power Fire System Power FormulaTelephone Connections Called Party Disconnect Operation Monitor LED GreenDialing Format Phone Line MonitorPosition Ground Start Ground StartPhone Monitor Select Jumper Loop StartD7212G Point Parameters On-board PointsDescription Terminals Point Sensor LoopsBell Point Zonex Bus D7212G Terminals Off-board PointsD8125, D8127 and D9127 Popit Modules Installing the D8125 Popex ModulePopit Sensor Loops Wiring Data Expansion Loops to Popex ModulesExpansion Loops Combined Length in ft. mConnecting the D8125 Popex to the D7212G Panel Radxpnts Handler Popit Module Point AssignmentsProgram Record Sheet Description Installing the OctoPOPITD8128D OctoPOPIT Module Popit LabelsLine Termination Wiring OctoPOPITsOctoPOPIT Sensor Loops Testing Off-board PointsAddress Assignment Switches D8128D Address SwitchesConnecting D8128D OctoPOPITs to the D7212G D7212G D8129 OctoRelay Panel Relay D8129 OctoRelay D8129 OctoRelay Switch NumberOff-board Relays D8129 Connections to the D7212G Arming Devices Command Center TerminalsAssigning the command center an address Address SwitchPower at Command Centers D7212G Command Center Terminal FunctionMomentary Contact KeyswitchKeyswitch Operation Maintained Contact 10.3 D279A Independent Zone ControlD7212G 11.3 D9131A Parallel Printer Interface Module InstallationPrinter Switch SDI DevicesSDI Address 11.5.2 D9133TTL-E Network Interface Module Address SettingsD7212G Programmer Access Reports Programmer and Accessory ConnectionsProgrammer Connector Accessory ConnectorProgrammer and Accessory Connections AccessoryProgramming ConnectorConnector13.1 D7212G Faceplate Faceplate 13.0Faceplate D7212G Control/Communicator, 1 Appendix a System Wiring Diagrams, Issue aD7212G Control/Communicator, 2 D7212G System Wiring Diagram, 2D7212G Control/Communicator, 3 D7212G System Wiring Diagram, 3D7212G Zonex 1, Points 9 to Appendix B Point Address ChartD7212G Index SymbolsZonex