Bosch Appliances D7212G Arming Devices, Description, Command Center Terminals, Address Switch

Page 49

D7212G

Arming Devices

10.0Arming Devices

10.1Description

Command centers, maintained or momentary contact keyswitches, or a combination of the two are used to arm and disarm areas. The panel may contain up to 4 areas. See Section 2.4.2 Areas and Accounts on page 17 for a description of areas.

10.2Command Center Terminals

The Bosch Security Systems command center is a 4-wire powered device used to arm and disarm areas, annunciate complete system status, initiate system tests, and control many functions of the security system.

The system can supervise up to eight command centers. The panel transmits a serial device trouble report, SDI FAILURE in the Modem IIIa2 format or TROUBLE ZN D in the BFSK format, if it loses communication with a supervised command center. CALL FOR SERVICE appears in any command center with text display capability that loses communication with the panel. SERVC KEYPAD appears at all other command centers connected to the system.

A total of 32 command centers can be connected to the system. The number of supervised command centers, number of areas, and the available power affect the total number of command centers that can be connected to the system. See Command Center in the D7212G Program Entry Guide (P/N: 4998138538) for complete programming details on command center options.

There are five types of command centers available for use with the system:

•D1255: 16-character alphanumeric display for general use.

•D1256: text display command center with functional keys optimized for local fire alarm control.

•D1257: text display command center for fire annunciation.

•D1260: Easy-to-read 4-line by 20-character LCD display with eight “Soft” keys for displaying simple selections.

•D720: LED display command center appropriate for use as a single area command center with up to eight points. The D1255 and D720 are also available in white (D1255W and D720W) or red (D1255R and D720R) versions.

See the command center’s User’s Guide for operational information.

10.2.1Assigning the command center an address

Switches on the command center assign an address (1 to 8) to the command center. The address determines if the command center is supervised, the command center's scope, and what area the command center is assigned to. See Command Center Assignment in the D7212G Program Entry Guide (P/N: 4998138538) for a complete description of addresses.

Table 12 shows the correct switch setting for each address.

Address

 

 

Switch

 

 

1

2

3

4

5

6

 

Address #1

ON

ON

ON

ON

Encoding

ON

 

 

 

 

 

 

Address #2

OFF

ON

ON

ON

ON

 

 

 

 

 

 

Address #3

ON

OFF

ON

ON

ON

 

 

 

 

 

 

Address #4

OFF

OFF

ON

ON

ON

Tone

 

 

 

 

 

 

Address #5

ON

ON

OFF

ON

ON

 

 

 

 

 

ON/OFF

 

Address #6

OFF

ON

OFF

ON

ON

 

 

 

 

 

 

Address #7

ON

OFF

OFF

ON

ON

 

 

 

 

 

 

Address #8

OFF

OFF

OFF

ON

ON

 

 

 

 

 

 

 

 

Table 12: Command Cneter Address Settings

D7212G Operation and Installation Guide

© 2003 Bosch Security Systems

Page 49

4998138544C

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Control/Communicator D7212G D7212G Operation and Installation GuideContents 11.1 10.111.2 11.0 10.013.0 Figures Tables D7212G Operation and Installation Guide OrganizationGuide Organization IntroductionSection Description Appendix DescriptionDocumentation Conventions Related DocumentationType Styles Used in the Text Tips, Notes, Cautions and Warnings FCC RulesPart D7212G Overview New Features D9412G D7412G D7212G9000G Series Panel Differences Secondary SpecificationsTelephone Connections Telephone Line Compatible Accessories Features in D7212GGround Fault Detect IntroductionStandard Features Model Display Application Control/Communicator Assembly Other FeaturesComponents and Literature Available by Separate Order Burglary Listings and ApprovalsListings Beginning the Installation InstallationBefore Beginning Enclosure OptionsConnecting Earth Ground Installing the AssemblyGround Fault Detect Enable Locking the Reset PinCharge the Battery While Finishing Finishing the InstallationInstall and Wire Detection Devices Install Modules and RelaysTesting the System Install the Point Chart LabelProgramming the Panel Primary Power Terminals Power SupplySecondary Power Terminals Replacing the Battery Installing the BatteryBattery Charging Circuit Float Charge Battery SupervisionBattery Discharge/Recharge Schedule Discharge CycleType Charging Status and Low Battery LEDsAction Color StateTotal Available Power Power OutputsAux Power Terminals Continuous Current Draw Programmable Power Outputs TerminalsAvailable Power Relay InstallationFire System Power Formula Verification/Reset RelayTelephone Connections Dialing Format Operation Monitor LED GreenPhone Line Monitor Called Party DisconnectPhone Monitor Select Jumper Ground StartLoop Start Position Ground StartD7212G Description Terminals On-board PointsPoint Sensor Loops Point ParametersBell Point Zonex Bus D7212G Terminals Off-board PointsD8125, D8127 and D9127 Popit Modules Installing the D8125 Popex ModuleExpansion Loops Combined Wiring Data Expansion Loops to Popex ModulesLength in ft. m Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Program Record Sheet Popit Module Point AssignmentsRadxpnts Handler D8128D OctoPOPIT Module Installing the OctoPOPITPopit Labels DescriptionLine Termination Wiring OctoPOPITsAddress Assignment Switches Testing Off-board PointsD8128D Address Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G Off-board Relays Panel Relay D8129 OctoRelay D8129 OctoRelay Switch NumberD8129 OctoRelay D8129 Connections to the D7212G Assigning the command center an address Command Center TerminalsAddress Switch Arming DevicesPower at Command Centers D7212G Command Center Terminal FunctionKeyswitch Operation Maintained Contact Keyswitch10.3 D279A Independent Zone Control Momentary ContactD7212G Printer Switch InstallationSDI Devices 11.3 D9131A Parallel Printer Interface ModuleSDI Address 11.5.2 D9133TTL-E Network Interface Module Address SettingsD7212G Programmer Connector Programmer and Accessory ConnectionsAccessory Connector Programmer Access ReportsProgrammer and Accessory Connections AccessoryProgramming ConnectorConnector13.1 D7212G Faceplate Faceplate 13.0Faceplate D7212G Control/Communicator, 1 Appendix a System Wiring Diagrams, Issue aD7212G Control/Communicator, 2 D7212G System Wiring Diagram, 2D7212G Control/Communicator, 3 D7212G System Wiring Diagram, 3D7212G Zonex 1, Points 9 to Appendix B Point Address ChartD7212G Index SymbolsZonex
Top Page Image Contents