Bosch Appliances D7212G SDI Devices, Installation, 11.3 D9131A Parallel Printer Interface Module

Page 53

D7212G

SDI Devices

11.0SDI Devices

11.1Description

The D7212G Panel can support a number of accessory devices off the SDI bus using Terminals 29 through 32. Some devices include the Command Centers (discussed in the previous section), the D9131A Parallel Printer Interface Module, the D9133 Serial Interface Module, the D9133DC Direct Connect Module, and the D9133TTL-E Network Interface Module.

11.2Installation

Consult the Operation and Installation Guide of the specific SDI device for complete installation instructions. SDI devices connect to the panel in parallel as shown in Table 14.

These devices may share power with the panel or be powered by a stand-alone power source.

D7212G

SDI Devices

Terminal

Function

Wire Color

Function

32

POWER +

Red

+12 VDC

 

 

 

 

31

DATA BUS A

Yellow

Data-In

 

 

 

 

30

DATA BUS B

Green

Data-Out

 

 

 

 

29

COMMON

Black

Common

 

 

 

 

Table 14: SDI Device Connections

A stand-alone power supply powering any SDI device must also be connected to a common terminal on the panel. Do not connect the stand-alone power supply’s earth ground to Terminal 10 on the panel.

IMPORTANT

11.3D9131A Parallel Printer Interface Module

The Bosch Security Systems D9131A Parallel Printer Interface Module is a 4-wire powered device used to connect a standard parallel printer to a panel. The D7212G can supervise one printer. Each printer requires a separate D9131A Parallel Printer Interface Module. The D9131A connects to the printer using a standard parallel printer cable.

11.3.1Switch Settings

Switches on the D9131A assign the address to the printer. The address determines if the printer is supervised, the printer's scope, and the area to which the printer is assigned. See Printer Parameters in the D7212G Program Entry Guide (P/N: 4998138538) for a complete description of addresses.

Table 15 shows the correct switch setting for Address 17.

Printer

 

 

Switch

 

 

1

2

3

4

5

6

 

17

ON

ON

ON

*

ON

ON

 

 

 

 

 

 

 

* ON = Header and Form Feed

 

 

 

OFF = No Header and No Form Feed

 

 

 

 

 

 

 

 

 

Table 15: Printer Address Switch Settings

11.3.2Supervision

Supervision includes proper operation of the SDI bus, proper connection of the printer cable between the printer and the D9131A, printer paper supply, printer selected (on-line), and printer power.

The panel sends an SDI failure report to the receiver if it fails to communicate with the printer interface, and

SERVC PRINTER displays at the command center. The report to the receiver includes the address of the troubled D9131A to indicate which printer needs service.

If an SDI device is supervised and SDI A becomes disconnected, the device may still operate normally, depending upon environmental conditions.

D7212G Operation and Installation Guide

© 2003 Bosch Security Systems

Page 53

4998138544C

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Control/Communicator D7212G D7212G Operation and Installation GuideContents 11.2 10.111.1 11.0 10.013.0 Figures Tables D7212G Operation and Installation Guide OrganizationGuide Organization IntroductionSection Description Appendix DescriptionType Styles Used in the Text Related DocumentationDocumentation Conventions Part FCC RulesTips, Notes, Cautions and Warnings D7212G 9000G Series Panel Differences New Features D9412G D7412G D7212GOverview Secondary SpecificationsTelephone Connections Telephone Line Compatible Accessories Features in D7212GGround Fault Detect IntroductionStandard Features Model Display Application Components and Literature Available by Separate Order Other FeaturesControl/Communicator Assembly Listings Listings and ApprovalsBurglary Beginning the Installation InstallationBefore Beginning Enclosure OptionsConnecting Earth Ground Installing the AssemblyGround Fault Detect Enable Locking the Reset PinCharge the Battery While Finishing Finishing the InstallationInstall and Wire Detection Devices Install Modules and RelaysProgramming the Panel Install the Point Chart LabelTesting the System Secondary Power Terminals Power SupplyPrimary Power Terminals Replacing the Battery Installing the BatteryBattery Charging Circuit Float Charge Battery SupervisionBattery Discharge/Recharge Schedule Discharge CycleType Charging Status and Low Battery LEDsAction Color StateTotal Available Power Power OutputsAux Power Terminals Continuous Current Draw Programmable Power Outputs TerminalsAvailable Power Relay InstallationFire System Power Formula Verification/Reset RelayTelephone Connections Dialing Format Operation Monitor LED GreenPhone Line Monitor Called Party DisconnectPhone Monitor Select Jumper Ground StartLoop Start Position Ground StartD7212G Description Terminals On-board PointsPoint Sensor Loops Point ParametersBell Point Zonex Bus D7212G Terminals Off-board PointsD8125, D8127 and D9127 Popit Modules Installing the D8125 Popex ModuleExpansion Loops Combined Wiring Data Expansion Loops to Popex ModulesLength in ft. m Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Radxpnts Handler Popit Module Point AssignmentsProgram Record Sheet D8128D OctoPOPIT Module Installing the OctoPOPITPopit Labels DescriptionLine Termination Wiring OctoPOPITsAddress Assignment Switches Testing Off-board PointsD8128D Address Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G D8129 OctoRelay Panel Relay D8129 OctoRelay D8129 OctoRelay Switch NumberOff-board Relays D8129 Connections to the D7212G Assigning the command center an address Command Center TerminalsAddress Switch Arming DevicesPower at Command Centers D7212G Command Center Terminal FunctionKeyswitch Operation Maintained Contact Keyswitch10.3 D279A Independent Zone Control Momentary ContactD7212G Printer Switch InstallationSDI Devices 11.3 D9131A Parallel Printer Interface ModuleSDI Address 11.5.2 D9133TTL-E Network Interface Module Address SettingsD7212G Programmer Connector Programmer and Accessory ConnectionsAccessory Connector Programmer Access ReportsProgrammer and Accessory Connections AccessoryProgramming ConnectorConnector13.1 D7212G Faceplate Faceplate 13.0Faceplate D7212G Control/Communicator, 1 Appendix a System Wiring Diagrams, Issue aD7212G Control/Communicator, 2 D7212G System Wiring Diagram, 2D7212G Control/Communicator, 3 D7212G System Wiring Diagram, 3D7212G Zonex 1, Points 9 to Appendix B Point Address ChartD7212G Index SymbolsZonex
Top Page Image Contents