Bosch Appliances D7212G manual Introduction, Guide Organization, Section Description

Page 9

D7212G

Introduction

1.0Introduction

This guide addresses the operation and installation of the D7212G Control/Communicator only and should not be used in conjunction with the D9412G, D7412G, D9412, D9112, D9112B1, D7412, D7212 or D7212B1 Panels.

Throughout this guide, unless expressly stated, the words “panel” and “control/communicator” refer to the D7212G.

Section 2.1 9000G Series Panel Differences on page 13 provides an overview of the differences between the D9412G, D7412G, and D7212G panels.

1.1Guide Organization

This guide is divided into sections and appendices, summarized in Table 1.

Section

Description

 

 

1

Introduction – provides information on the structure of the guide, lists other literature related

 

to this control/communicator, and describes the FCC rules with which it complies.

 

 

2

Overview – provides an overview of the D7212G Control/Communicator, including operational

 

specifications and standard features.

 

 

3

Installation – provides installation instructions for connecting the power terminals plus the

 

status and battery LEDs.

 

 

4

Power Supply – provides information on the primary and secondary modules and instructions

 

on connecting and programming them.

 

 

5

Power Outputs – provides information on the power outputs and instructions on installing the

 

transformer; explains the status and battery LEDs.

 

 

6

Telephone Connections – provides information on connecting the phone line and

 

programming it for use.

 

 

7

On-Board Points – provides information on the on-board points and their parameters.

 

 

8

Off-Board Points – provides information on the off-board points and their parameters,

 

including the installation, wiring and testing of OctoPOPITs.

 

 

9

Off-Board Relays – describes the installation and wiring of the D8129 OctoRelay.

 

 

10

Arming Devices – describes the installation, wiring, programming and operation of

 

independent zone control modules.

 

 

11

SDI Devices – provides a description and installation instructions for various SDI device

 

modules.

 

 

12

Programmer and Accessory Connections – describes the Programmer Connector and the

 

Accessory Connector.

 

 

13

Faceplate – provides an illustration of the D7212G panel

 

 

Appendix

Description

 

 

A

System Wiring Diagrams – illustrations showing the terminal wiring connections for the

 

D7212G.

 

 

B

Point Address Chart – provides ZONEX point addresses for POPITS.

 

 

Table 1: D7212G Operation and Installation Guide Organization

D7212G Operation and Installation Guide

© 2003 Bosch Security Systems

Page 9

4998138544C

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Control/Communicator D7212G D7212G Operation and Installation GuideContents 10.1 11.111.2 11.0 10.013.0 Figures Tables D7212G Operation and Installation Guide OrganizationGuide Organization IntroductionSection Description Appendix DescriptionRelated Documentation Documentation ConventionsType Styles Used in the Text FCC Rules Tips, Notes, Cautions and WarningsPart D7212G New Features D9412G D7412G D7212G Overview9000G Series Panel Differences Secondary SpecificationsTelephone Connections Telephone Line Compatible Accessories Features in D7212GGround Fault Detect IntroductionStandard Features Model Display Application Other Features Control/Communicator AssemblyComponents and Literature Available by Separate Order Listings and Approvals BurglaryListings Beginning the Installation InstallationBefore Beginning Enclosure OptionsConnecting Earth Ground Installing the AssemblyGround Fault Detect Enable Locking the Reset PinCharge the Battery While Finishing Finishing the InstallationInstall and Wire Detection Devices Install Modules and RelaysInstall the Point Chart Label Testing the SystemProgramming the Panel Power Supply Primary Power TerminalsSecondary Power Terminals Replacing the Battery Installing the BatteryBattery Charging Circuit Float Charge Battery SupervisionBattery Discharge/Recharge Schedule Discharge CycleType Charging Status and Low Battery LEDsAction Color StateTotal Available Power Power OutputsAux Power Terminals Continuous Current Draw Programmable Power Outputs TerminalsAvailable Power Relay InstallationFire System Power Formula Verification/Reset RelayTelephone Connections Dialing Format Operation Monitor LED GreenPhone Line Monitor Called Party DisconnectPhone Monitor Select Jumper Ground StartLoop Start Position Ground StartD7212G Description Terminals On-board PointsPoint Sensor Loops Point ParametersBell Point Zonex Bus D7212G Terminals Off-board PointsD8125, D8127 and D9127 Popit Modules Installing the D8125 Popex ModuleExpansion Loops Combined Wiring Data Expansion Loops to Popex ModulesLength in ft. m Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Popit Module Point Assignments Program Record SheetRadxpnts Handler D8128D OctoPOPIT Module Installing the OctoPOPITPopit Labels DescriptionLine Termination Wiring OctoPOPITsAddress Assignment Switches Testing Off-board PointsD8128D Address Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G Panel Relay D8129 OctoRelay D8129 OctoRelay Switch Number Off-board RelaysD8129 OctoRelay D8129 Connections to the D7212G Assigning the command center an address Command Center TerminalsAddress Switch Arming DevicesPower at Command Centers D7212G Command Center Terminal FunctionKeyswitch Operation Maintained Contact Keyswitch10.3 D279A Independent Zone Control Momentary ContactD7212G Printer Switch InstallationSDI Devices 11.3 D9131A Parallel Printer Interface ModuleSDI Address 11.5.2 D9133TTL-E Network Interface Module Address SettingsD7212G Programmer Connector Programmer and Accessory ConnectionsAccessory Connector Programmer Access ReportsProgrammer and Accessory Connections AccessoryProgramming ConnectorConnector13.1 D7212G Faceplate Faceplate 13.0Faceplate D7212G Control/Communicator, 1 Appendix a System Wiring Diagrams, Issue aD7212G Control/Communicator, 2 D7212G System Wiring Diagram, 2D7212G Control/Communicator, 3 D7212G System Wiring Diagram, 3D7212G Zonex 1, Points 9 to Appendix B Point Address ChartD7212G Index SymbolsZonex
Top Page Image Contents