Bosch Appliances D7212G manual Other Features, Control/Communicator Assembly

Page 19

D7212G

Overview

2.4.10Other Features

The D7212G Control/Communicator has many programmable features. A short list of some of the features follows. Complete details on all the features can be found in the D7212G Program Entry Guide (P/N: 4998138538).

•Supervision of AC (primary power), battery (secondary power), ZONEX and SDI buses, the CPU (Central Processing Unit), up to three printers, and two telephone lines

•Automatic system test reports

•Remote access for programming, diagnostics, and log uploads using the Remote Account Manager (RAM IV)

•Fire Alarm Verification

•Programmable Alarm Output

•Programmable Relay Output using the D8129 OctoRelay Module

•Opening and Closing Windows

•Skeds (scheduled events)

2.4.11Control/Communicator Assembly

The D7212G Control/Communicator is shipped pre-assembled from the factory with the following parts:

•Literature Pack

-D7212G Approved Applications Compliance Guide (P/N: 4998138560)

-D7212G Operation and Installation Guide (P/N: 4998138544)

-D7212G Program Entry Guide (P/N: 4998138538)

-D7212G Program Record Sheet (P/N: 4998138542)

-D7212G Release Notes (P/N: 4998138543)

-D9412G/D7412G/D7212G Installation and Troubleshooting Quick Reference Guide (P/N: 43700)

-9000/9000G Series Technogram: Smoke Detector Compatibility (P/N: 33284)

-7000/9000 Series Point Chart Label (P/N: 79-06660-000)

•Assembly

-PC Board

-Faceplate Shield

-Mounting Skirt

-One #6 x1/4 in. Screw

2.4.12Components and Literature Available by Separate Order

Order the following components separately to complete a basic 8 point installation:

•D1255, D1256, D1257, D1260, or D720 Command Center (or keyswitch)

•D1640 Transformer

•D126 or D1218 Battery

•D161 or D162 Phone Cord

•D8103, D8108A, or D8109 Enclosure

Configured packages are also available. Please consult the Bosch Security Systems Intrusion Catalog.

D7212G Operation and Installation Guide

© 2003 Bosch Security Systems

Page 19

4998138544C

Image 19

Contents Control/Communicator D7212G D7212G Operation and Installation GuideContents 11.1 10.111.2 11.0 10.013.0 Figures Tables D7212G Operation and Installation Guide OrganizationAppendix Description IntroductionGuide Organization Section DescriptionDocumentation Conventions Related DocumentationType Styles Used in the Text Tips, Notes, Cautions and Warnings FCC RulesPart D7212G Overview New Features D9412G D7412G D7212G9000G Series Panel Differences Secondary SpecificationsTelephone Connections Telephone Line Introduction Features in D7212GCompatible Accessories Ground Fault DetectStandard Features Model Display Application Control/Communicator Assembly Other FeaturesComponents and Literature Available by Separate Order Burglary Listings and ApprovalsListings Enclosure Options InstallationBeginning the Installation Before BeginningLocking the Reset Pin Installing the AssemblyConnecting Earth Ground Ground Fault Detect EnableInstall Modules and Relays Finishing the InstallationCharge the Battery While Finishing Install and Wire Detection DevicesTesting the System Install the Point Chart LabelProgramming the Panel Primary Power Terminals Power SupplySecondary Power Terminals Replacing the Battery Installing the BatteryDischarge Cycle Battery SupervisionBattery Charging Circuit Float Charge Battery Discharge/Recharge ScheduleColor State Charging Status and Low Battery LEDsType ActionProgrammable Power Outputs Terminals Power OutputsTotal Available Power Aux Power Terminals Continuous Current DrawVerification/Reset Relay Relay InstallationAvailable Power Fire System Power FormulaTelephone Connections Called Party Disconnect Operation Monitor LED GreenDialing Format Phone Line MonitorPosition Ground Start Ground StartPhone Monitor Select Jumper Loop StartD7212G Point Parameters On-board PointsDescription Terminals Point Sensor LoopsBell Point Zonex Bus D7212G Terminals Off-board PointsD8125, D8127 and D9127 Popit Modules Installing the D8125 Popex ModulePopit Sensor Loops Wiring Data Expansion Loops to Popex ModulesExpansion Loops Combined Length in ft. mConnecting the D8125 Popex to the D7212G Panel Program Record Sheet Popit Module Point AssignmentsRadxpnts Handler Description Installing the OctoPOPITD8128D OctoPOPIT Module Popit LabelsLine Termination Wiring OctoPOPITsOctoPOPIT Sensor Loops Testing Off-board PointsAddress Assignment Switches D8128D Address SwitchesConnecting D8128D OctoPOPITs to the D7212G D7212G Off-board Relays Panel Relay D8129 OctoRelay D8129 OctoRelay Switch NumberD8129 OctoRelay D8129 Connections to the D7212G Arming Devices Command Center TerminalsAssigning the command center an address Address SwitchPower at Command Centers D7212G Command Center Terminal FunctionMomentary Contact KeyswitchKeyswitch Operation Maintained Contact 10.3 D279A Independent Zone ControlD7212G 11.3 D9131A Parallel Printer Interface Module InstallationPrinter Switch SDI DevicesSDI Address 11.5.2 D9133TTL-E Network Interface Module Address SettingsD7212G Programmer Access Reports Programmer and Accessory ConnectionsProgrammer Connector Accessory ConnectorProgrammer and Accessory Connections AccessoryProgramming ConnectorConnector13.1 D7212G Faceplate Faceplate 13.0Faceplate D7212G Control/Communicator, 1 Appendix a System Wiring Diagrams, Issue aD7212G Control/Communicator, 2 D7212G System Wiring Diagram, 2D7212G Control/Communicator, 3 D7212G System Wiring Diagram, 3D7212G Zonex 1, Points 9 to Appendix B Point Address ChartD7212G Index SymbolsZonex