Bosch Appliances Comprehensive Guide to Bosch D8125 POPEX and D9127 POPIT Module Installation and Addressing
Page 38

D7212G

Off-board Points

8.2D8125, D8127 and D9127 POPIT Modules

D8127 and D9127 POPITs use the D8125 POPEX Module to report to the panel. The D8125 supports up to 32 POPIT points (Points 9 to 20). The panel only annunciates activity for each POPIT, not each detection device connected to the sensor loop.

There are two versions of the D8127 and D9127 Modules. Both module enclosures are made of UL Listed fire resistant material. D8127T and D9127T Modules contain tamper switches. D8127U and D9127U Modules come with untampered covers. Unless the module is mounted in a tampered enclosure, UL requires D8127T and D9127T Modules for certificated accounts.

8.2.1Listings

The D8125 POPEX and the D8127 and D9127 POPIT Modules are UL Listed for use with the D7212G for each of the categories listed in Section 2.4.13 Listings and Approvals on page 20. See the D7212G Approved Applications Compliance Guide (P/N: 4998138560) to determine the required equipment and enclosures for the application.

8.3Installing the D8125 POPEX Module

For information on the Multiplex Bus Interface, see the D8125MUX Operation and Installation Guide (P/N: 36796).

IMPORTANT

Save the POPIT Label Sheets: The D8125 is packaged with two sets of POPIT label sheets. One is marked for use with the D9412/D9112. Save this set for use with the D7212G. It will be used later to label the POPITs.

8.3.1Mounting

Use the following procedure to install the D8125 in the enclosure with the panel:

1.Align the D8125 POPEX Module with any of the four mounting locations in the enclosure. See Figure 2 on page 21.

2.Use the screws provided with the module to secure it in the enclosure.

8.3.2Wiring the D8125 to the Control/Communicator

Follow the procedure below to wire one or two D8125 POPEX Modules to the panel. See Figure 13 on page 39.

Power down first: Power down the panel by disconnecting the positive (red) battery lead at the battery and unplugging the transformer.

For Points 9 to 40:

1.Connect the GND terminal of the D8125 to Terminal 9 on the D7212G.

2.Connect the OUT terminal of the D8125 to ZONEX IN 1, Terminal 27.

3.Connect the IN terminal of the D8125 to ZONEX OUT 1, Terminal 28.

4.Connect the AUX terminal of the D8125 to Terminal 3 on the D7212G.

See Section 8.3.4 Wiring Data Expansion Loops to POPEX Modules on page 39 for instructions on connecting POPITs to the D8125 POPEX Module.

8.3.3Wiring POPITs to the Data Expansion Loop

Use one 2-wire data expansion loop or distribute the POPITs on up to three loops. Setting DIP switches on the POPIT Modules assigns them to point numbers. See Section 8.3.6 POPIT Module Point Assignments on page 41.

Review Section 3.6.2 Install and Wire Detection Devices on page 23 to determine if shielded wire is required. Determine the required wire gauge for the length of each data expansion loop using Table 9 on page 39.

D7212G Operation and Installation Guide

4998138544C

Page 38

© 2003 Bosch Security Systems

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Control/Communicator D7212G Operation and Installation Guide D7212GContents 11.2 10.111.1 10.0 11.013.0 Figures D7212G Operation and Installation Guide Organization TablesSection Description IntroductionGuide Organization Appendix DescriptionType Styles Used in the Text Related DocumentationDocumentation Conventions Part FCC RulesTips, Notes, Cautions and Warnings D7212G 9000G Series Panel Differences New Features D9412G D7412G D7212GOverview Specifications SecondaryTelephone Connections Telephone Line Ground Fault Detect Features in D7212GCompatible Accessories IntroductionStandard Features Model Display Application Components and Literature Available by Separate Order Other FeaturesControl/Communicator Assembly Listings Listings and ApprovalsBurglary Before Beginning InstallationBeginning the Installation Enclosure OptionsGround Fault Detect Enable Installing the AssemblyConnecting Earth Ground Locking the Reset PinInstall and Wire Detection Devices Finishing the InstallationCharge the Battery While Finishing Install Modules and RelaysProgramming the Panel Install the Point Chart LabelTesting the System Secondary Power Terminals Power SupplyPrimary Power Terminals Installing the Battery Replacing the BatteryBattery Discharge/Recharge Schedule Battery SupervisionBattery Charging Circuit Float Charge Discharge CycleAction Charging Status and Low Battery LEDsType Color StateAux Power Terminals Continuous Current Draw Power OutputsTotal Available Power Programmable Power Outputs TerminalsFire System Power Formula Relay InstallationAvailable Power Verification/Reset RelayTelephone Connections Phone Line Monitor Operation Monitor LED GreenDialing Format Called Party DisconnectLoop Start Ground StartPhone Monitor Select Jumper Position Ground StartD7212G Point Sensor Loops On-board PointsDescription Terminals Point ParametersBell Off-board Points Point Zonex Bus D7212G TerminalsInstalling the D8125 Popex Module D8125, D8127 and D9127 Popit ModulesLength in ft. m Wiring Data Expansion Loops to Popex ModulesExpansion Loops Combined Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Radxpnts Handler Popit Module Point AssignmentsProgram Record Sheet Popit Labels Installing the OctoPOPITD8128D OctoPOPIT Module DescriptionWiring OctoPOPITs Line TerminationD8128D Address Switches Testing Off-board PointsAddress Assignment Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G D8129 OctoRelay Panel Relay D8129 OctoRelay D8129 OctoRelay Switch NumberOff-board Relays D8129 Connections to the D7212G Address Switch Command Center TerminalsAssigning the command center an address Arming DevicesD7212G Command Center Terminal Function Power at Command Centers10.3 D279A Independent Zone Control KeyswitchKeyswitch Operation Maintained Contact Momentary ContactD7212G SDI Devices InstallationPrinter Switch 11.3 D9131A Parallel Printer Interface ModuleSDI Address Address Settings 11.5.2 D9133TTL-E Network Interface ModuleD7212G Accessory Connector Programmer and Accessory ConnectionsProgrammer Connector Programmer Access ReportsAccessoryProgramming ConnectorConnector Programmer and Accessory ConnectionsFaceplate 13.0 13.1 D7212G FaceplateFaceplate Appendix a System Wiring Diagrams, Issue a D7212G Control/Communicator, 1D7212G System Wiring Diagram, 2 D7212G Control/Communicator, 2D7212G System Wiring Diagram, 3 D7212G Control/Communicator, 3D7212G Appendix B Point Address Chart Zonex 1, Points 9 toD7212G Symbols IndexZonex
Top Page Image Contents