Bosch Appliances Comprehensive Guide to Bosch D8128D Addressing, OctoPOPIT and POPIT Modules
Page 42

D7212G

Off-board Points

POPIT Labels

Off-board points for the D7212G are numbered 9 to 40.

Two sheets of peel-off POPIT labels are supplied with the D8125 POPEX Module. Use the sheet marked Bank1 for Points 9 to 40.

Each label has two parts. Place the smaller part, with just the point number on it, on the chip. Place the larger part with the switch settings on the base of the POPIT. Set the switches and cover the POPIT.

Do not program two POPITs for the same point number. After programming all the points, perform a service walk test. The D9412G/D7412G/D7212G Installation and Troubleshooting Quick Reference Guide (P/N: 43700) contains instructions for performing a service walk test. If a point does not test, check the programming for a duplicated address.

Walk test does not show extra points: If the point assignment switches on a POPIT or OctoPOPIT are set incorrectly, it may create both missing and extra point conditions. If the same point number is assigned to two or more POPITs or OctoPOPITs, none of the points with that number will test correctly. Refer to Section 8.1 Point (ZONEX) Bus D7212G Terminals 27 to 28 on page 37 for additional infomation on how to troubleshoot POPITs or extra point conditions.

8.4D8128D OctoPOPIT Module

D8128, D8128A or D8128B modules are not compatible with the D7212G. Only use the D8128D OctoPOPIT module. Using D8128, D8128A or D8128B modules may cause intermittent missing and restoral reports.

IMPORTANT

8.4.1Description

The D8128D OctoPOPIT Module combines the functions of the D8125 POPEX module and the D8127/D9127 POPIT modules to provide eight off-board points in a single module. You can wire both D8128D OctoPOPIT and D8125 POPEX modules in parallel to the ZONEX Bus terminals on the same panel.

Review Section 5.0 Power Outputs on page 29 to be sure to provide enough power for the OctoPOPITs and other powered devices that will be connected to the system.

8.4.2Listing

The D8128D OctoPOPIT Module is UL Listed for Local or Police Connected Burglary Alarm, Central Station Burglary Alarm, and Household Burglary Alarm applications. The D8128D is also suitable for fire supervisory applications, such as indicating circuit supervision (using the D192C/D192G Bell Circuit Supervision Module), sprinkler supervision, and valve tamper protection.

Do not connect fire alarm initiating devices directly to the D8128D.

You must use the D125B Dual Class B Powered Loop Interface Module or D129 Dual Class A Initiation Circuit Module for fire initiation applications. Connect the initiating devices, smoke detectors for example, to the D125B powered loops or D129 Class A loops.

Connect the zone outputs on the D125B or D129 to the OctoPOPIT sensor loop inputs. The D125B or D129 and the OctoPOPIT must be mounted in the enclosure with the panel or in a separate enclosure connected to the panel’s enclosure by conduit no longer than 20 ft. (6 m).

8.4.3Installing the OctoPOPIT

You can install the D8128D OctoPOPIT Module in the enclosure with the panel, or in a separate enclosure (D8103, D8108A, or D8109) up to 200 ft. (61 m) from the panel, using standard four-conductor 22 AWG (0.8 mm) wire. If you mount the OctoPOPIT in a separate enclosure, use shielded cable to avoid electro-magnetic interference. See EMI on Long Wire Runs in the D9412G/D7412G/D7212G Installation and Troubleshooting Quick Reference Guide (P/N: 43700).

Tampered enclosures for UL Certificated systems: The D125B or D129 and the OctoPOPIT must be mounted in the enclosure with the panel or in a separate enclosure connected to the panel’s enclosure by conduit not more than 20 ft. (6 m) in length.

D7212G Operation and Installation Guide

4998138544C

Page 42

© 2003 Bosch Security Systems

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Control/Communicator D7212G Operation and Installation Guide D7212GContents 10.1 11.111.2 10.0 11.013.0 Figures D7212G Operation and Installation Guide Organization TablesSection Description IntroductionGuide Organization Appendix DescriptionRelated Documentation Documentation ConventionsType Styles Used in the Text FCC Rules Tips, Notes, Cautions and WarningsPart D7212G New Features D9412G D7412G D7212G Overview9000G Series Panel Differences Specifications SecondaryTelephone Connections Telephone Line Ground Fault Detect Features in D7212GCompatible Accessories IntroductionStandard Features Model Display Application Other Features Control/Communicator AssemblyComponents and Literature Available by Separate Order Listings and Approvals BurglaryListings Before Beginning InstallationBeginning the Installation Enclosure OptionsGround Fault Detect Enable Installing the AssemblyConnecting Earth Ground Locking the Reset PinInstall and Wire Detection Devices Finishing the InstallationCharge the Battery While Finishing Install Modules and RelaysInstall the Point Chart Label Testing the SystemProgramming the Panel Power Supply Primary Power TerminalsSecondary Power Terminals Installing the Battery Replacing the BatteryBattery Discharge/Recharge Schedule Battery SupervisionBattery Charging Circuit Float Charge Discharge CycleAction Charging Status and Low Battery LEDsType Color StateAux Power Terminals Continuous Current Draw Power OutputsTotal Available Power Programmable Power Outputs TerminalsFire System Power Formula Relay InstallationAvailable Power Verification/Reset RelayTelephone Connections Phone Line Monitor Operation Monitor LED GreenDialing Format Called Party DisconnectLoop Start Ground StartPhone Monitor Select Jumper Position Ground StartD7212G Point Sensor Loops On-board PointsDescription Terminals Point ParametersBell Off-board Points Point Zonex Bus D7212G TerminalsInstalling the D8125 Popex Module D8125, D8127 and D9127 Popit ModulesLength in ft. m Wiring Data Expansion Loops to Popex ModulesExpansion Loops Combined Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Popit Module Point Assignments Program Record SheetRadxpnts Handler Popit Labels Installing the OctoPOPITD8128D OctoPOPIT Module DescriptionWiring OctoPOPITs Line TerminationD8128D Address Switches Testing Off-board PointsAddress Assignment Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G Panel Relay D8129 OctoRelay D8129 OctoRelay Switch Number Off-board RelaysD8129 OctoRelay D8129 Connections to the D7212G Address Switch Command Center TerminalsAssigning the command center an address Arming DevicesD7212G Command Center Terminal Function Power at Command Centers10.3 D279A Independent Zone Control KeyswitchKeyswitch Operation Maintained Contact Momentary ContactD7212G SDI Devices InstallationPrinter Switch 11.3 D9131A Parallel Printer Interface ModuleSDI Address Address Settings 11.5.2 D9133TTL-E Network Interface ModuleD7212G Accessory Connector Programmer and Accessory ConnectionsProgrammer Connector Programmer Access ReportsAccessoryProgramming ConnectorConnector Programmer and Accessory ConnectionsFaceplate 13.0 13.1 D7212G FaceplateFaceplate Appendix a System Wiring Diagrams, Issue a D7212G Control/Communicator, 1D7212G System Wiring Diagram, 2 D7212G Control/Communicator, 2D7212G System Wiring Diagram, 3 D7212G Control/Communicator, 3D7212G Appendix B Point Address Chart Zonex 1, Points 9 toD7212G Symbols IndexZonex
Top Page Image Contents