Bosch Appliances D7212G manual Installation, Before Beginning, Enclosure Options

Page 21

D7212G

Installation

3.0Installation

3.1Before Beginning

This section contains a general installation procedure and provides references to other sections of the guide for detailed instructions.

Bosch Security Systems recommends a review of this guide and the D7212G Program Entry Guide (P/N: 4998138538) before beginning the installation to determine the hardware and wiring requirements for the features that will be used.

Have the following additional documents available when reading through this guide:

•D7212G Program Record Sheet (P/N: 4998138542)

•Security System Owner’s Manual (P/N: 71-06633-000)

•Command Center Installation Manual (D1255, D1256, D1257, D1260, or D720)

Before beginning the installation, become familiar with the operation of the D5200 Programmer or the Remote Account Manager (RAM IV).

3.2Enclosure Options

Mount the control/communicator assembly in any of the Bosch Security Systems enclosures listed below. Refer to the D7212G Approved Applications Compliance Guide (P/N: 4998138560) to determine if the application requires a specific enclosure.

•D8103 Universal Enclosure (tan)

•D8109 Fire Enclosure (red)

•D8108A Attack Resistant Enclosure (tan)

3.3Beginning the Installation

1.Mount the enclosure in the desired location. Use all five mounting holes. See Figure 2.

		MODULE MOUNTING
POINT CHART LABEL	MOUNTING	LOCATIONS
POINT CHART LABEL	SKIRT HOOK	TAMPER SWITCH
		MOUNTING LOCATION

MOUNTING

SKIRT HOOK

MODULE

MOUNTING

LOCATIONS

MOUNTING

SKIRT HOOK

OPENINGS

BACK OF

D7212G

LOCK DOWN TAB

SKIRT MOUNTING HOLE

Figure 2: Enclosure Mounting

2.Run the necessary wiring throughout the premises, and pull the wires into the enclosure.

Note: EMI (Electro Magnetic Interference) may cause problems. Refer to EMI on Long Wire Runs in the D9412G/D7412G/ D7212G Installation and Troubleshooting Quick Reference Guide (P/N: 43700).

D7212G Operation and Installation Guide

© 2003 Bosch Security Systems

Page 21

4998138544C

Image 21

Contents Control/Communicator D7212G D7212G Operation and Installation GuideContents 10.1 11.111.2 11.0 10.013.0 Figures Tables D7212G Operation and Installation Guide OrganizationGuide Organization IntroductionSection Description Appendix DescriptionRelated Documentation Documentation ConventionsType Styles Used in the Text FCC Rules Tips, Notes, Cautions and WarningsPart D7212G New Features D9412G D7412G D7212G Overview9000G Series Panel Differences Secondary SpecificationsTelephone Connections Telephone Line Compatible Accessories Features in D7212GGround Fault Detect IntroductionStandard Features Model Display Application Other Features Control/Communicator AssemblyComponents and Literature Available by Separate Order Listings and Approvals BurglaryListings Beginning the Installation InstallationBefore Beginning Enclosure OptionsConnecting Earth Ground Installing the AssemblyGround Fault Detect Enable Locking the Reset PinCharge the Battery While Finishing Finishing the InstallationInstall and Wire Detection Devices Install Modules and RelaysInstall the Point Chart Label Testing the SystemProgramming the Panel Power Supply Primary Power TerminalsSecondary Power Terminals Replacing the Battery Installing the BatteryBattery Charging Circuit Float Charge Battery SupervisionBattery Discharge/Recharge Schedule Discharge CycleType Charging Status and Low Battery LEDsAction Color StateTotal Available Power Power OutputsAux Power Terminals Continuous Current Draw Programmable Power Outputs TerminalsAvailable Power Relay InstallationFire System Power Formula Verification/Reset RelayTelephone Connections Dialing Format Operation Monitor LED GreenPhone Line Monitor Called Party DisconnectPhone Monitor Select Jumper Ground StartLoop Start Position Ground StartD7212G Description Terminals On-board PointsPoint Sensor Loops Point ParametersBell Point Zonex Bus D7212G Terminals Off-board PointsD8125, D8127 and D9127 Popit Modules Installing the D8125 Popex ModuleExpansion Loops Combined Wiring Data Expansion Loops to Popex ModulesLength in ft. m Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Popit Module Point Assignments Program Record SheetRadxpnts Handler D8128D OctoPOPIT Module Installing the OctoPOPITPopit Labels DescriptionLine Termination Wiring OctoPOPITsAddress Assignment Switches Testing Off-board PointsD8128D Address Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G Panel Relay D8129 OctoRelay D8129 OctoRelay Switch Number Off-board RelaysD8129 OctoRelay D8129 Connections to the D7212G Assigning the command center an address Command Center TerminalsAddress Switch Arming DevicesPower at Command Centers D7212G Command Center Terminal FunctionKeyswitch Operation Maintained Contact Keyswitch10.3 D279A Independent Zone Control Momentary ContactD7212G Printer Switch InstallationSDI Devices 11.3 D9131A Parallel Printer Interface ModuleSDI Address 11.5.2 D9133TTL-E Network Interface Module Address SettingsD7212G Programmer Connector Programmer and Accessory ConnectionsAccessory Connector Programmer Access ReportsProgrammer and Accessory Connections AccessoryProgramming ConnectorConnector13.1 D7212G Faceplate Faceplate 13.0Faceplate D7212G Control/Communicator, 1 Appendix a System Wiring Diagrams, Issue aD7212G Control/Communicator, 2 D7212G System Wiring Diagram, 2D7212G Control/Communicator, 3 D7212G System Wiring Diagram, 3D7212G Zonex 1, Points 9 to Appendix B Point Address ChartD7212G Index SymbolsZonex