Bosch Appliances D7212G manual Programmer and Accessory Connections, Programmer Connector

Page 57

D7212G

Programmer and Accessory Connections

12.0Programmer and Accessory Connections

12.1Programmer Connector

The procedure below shows how to connect and disconnect the programmer. Refer to the D5200 Programmer Manual (P/N: 74-06176-000) for complete information on using the D5200 programmer.

1.Lock Reset Pin: See Figure 19.

2.Connect the D5200 Data/Power cord into the programmer connector (refer to Figure 20 on page 58).

3.Perform the desired programming function (send or receive program).

4.Disconnect the programmer.

RESET PIN

LOCKED (CLOSED)

		Reset Pin
	Disable All Except Battery
	Charging And Programming
	PERIPHERAL DEVICE CONNECTIONS
	RED	POWER +	32	RESET PIN
				NORMAL (OPEN)
	YELLOW	DATA BUS A	31	FOR NORMAL
	YELLOW	DATA BUS A	31	PANEL
				PANEL
	GREEN	DATA BUS B	30	OPERATION
	GREEN	DATA BUS B	30
	BLACK	COMMON	29

Figure 19: Reset Pin

12.1.1Programmer Access Reports

When a program is sent to the panel, the panel sends a PROG ACCESS OK report ten seconds after the handler is exited or when the programmer is disconnected. The prompt in Routing must be programmed Yes for this report to be sent.

12.2Accessory Connector

The Accessory Connector is not used on the D7212G Control/Communicator.

D7212G Operation and Installation Guide

© 2003 Bosch Security Systems

Page 57

4998138544C

Image 57

Contents Control/Communicator D7212G D7212G Operation and Installation GuideContents 10.1 11.111.2 11.0 10.013.0 Figures Tables D7212G Operation and Installation Guide OrganizationGuide Organization IntroductionSection Description Appendix DescriptionRelated Documentation Documentation ConventionsType Styles Used in the Text FCC Rules Tips, Notes, Cautions and WarningsPart D7212G New Features D9412G D7412G D7212G Overview9000G Series Panel Differences Secondary SpecificationsTelephone Connections Telephone Line Compatible Accessories Features in D7212GGround Fault Detect IntroductionStandard Features Model Display Application Other Features Control/Communicator AssemblyComponents and Literature Available by Separate Order Listings and Approvals BurglaryListings Beginning the Installation InstallationBefore Beginning Enclosure OptionsConnecting Earth Ground Installing the AssemblyGround Fault Detect Enable Locking the Reset PinCharge the Battery While Finishing Finishing the InstallationInstall and Wire Detection Devices Install Modules and RelaysInstall the Point Chart Label Testing the SystemProgramming the Panel Power Supply Primary Power TerminalsSecondary Power Terminals Replacing the Battery Installing the BatteryBattery Charging Circuit Float Charge Battery SupervisionBattery Discharge/Recharge Schedule Discharge CycleType Charging Status and Low Battery LEDsAction Color StateTotal Available Power Power OutputsAux Power Terminals Continuous Current Draw Programmable Power Outputs TerminalsAvailable Power Relay InstallationFire System Power Formula Verification/Reset RelayTelephone Connections Dialing Format Operation Monitor LED GreenPhone Line Monitor Called Party DisconnectPhone Monitor Select Jumper Ground StartLoop Start Position Ground StartD7212G Description Terminals On-board PointsPoint Sensor Loops Point ParametersBell Point Zonex Bus D7212G Terminals Off-board PointsD8125, D8127 and D9127 Popit Modules Installing the D8125 Popex ModuleExpansion Loops Combined Wiring Data Expansion Loops to Popex ModulesLength in ft. m Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Popit Module Point Assignments Program Record SheetRadxpnts Handler D8128D OctoPOPIT Module Installing the OctoPOPITPopit Labels DescriptionLine Termination Wiring OctoPOPITsAddress Assignment Switches Testing Off-board PointsD8128D Address Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G Panel Relay D8129 OctoRelay D8129 OctoRelay Switch Number Off-board RelaysD8129 OctoRelay D8129 Connections to the D7212G Assigning the command center an address Command Center TerminalsAddress Switch Arming DevicesPower at Command Centers D7212G Command Center Terminal FunctionKeyswitch Operation Maintained Contact Keyswitch10.3 D279A Independent Zone Control Momentary ContactD7212G Printer Switch InstallationSDI Devices 11.3 D9131A Parallel Printer Interface ModuleSDI Address 11.5.2 D9133TTL-E Network Interface Module Address SettingsD7212G Programmer Connector Programmer and Accessory ConnectionsAccessory Connector Programmer Access ReportsProgrammer and Accessory Connections AccessoryProgramming ConnectorConnector13.1 D7212G Faceplate Faceplate 13.0Faceplate D7212G Control/Communicator, 1 Appendix a System Wiring Diagrams, Issue aD7212G Control/Communicator, 2 D7212G System Wiring Diagram, 2D7212G Control/Communicator, 3 D7212G System Wiring Diagram, 3D7212G Zonex 1, Points 9 to Appendix B Point Address ChartD7212G Index SymbolsZonex