Bosch Appliances D7212G manual SDI Address

Page 54

D7212G

SDI Devices

11.4SDI Address 80

SDI Address 80 is available on the D7212G Panel and allows bi-directional SDI to RS232 information. The intent of this address is for use with home or building automation software. A D9133 Serial Interface Module is required for this application.

11.4.1D9133 Serial Interface Module

The Bosch Security Systems D9133 Serial Interface Module is a four-wire powered SDI device providing connection for RS232 devices to the D7212G panel. The D9133 uses a specific communication protocol that is provided upon request. Please contact Bosch Security Systems Technical Support at (888) 886-6189.

The D9133 can be installed up to 1000 ft. (305 m) away from the panel using 18 AWG wire. The D9133 is not UL Listed.

D9133 Serial Interface Module

There are no jumper settings required for the D9133 (SDI Address

80)for home or building automation purposes. All Jumper shunts must be removed for this setting.

1

2

3

4

80

11.4.2Address Settings

11.4.3Supervision

The supervision of the D9133 is available through programming which includes proper operation between the D9133 and the control panel.

If supervised and the D9133 does not respond to panel supervision polls, the panel sends an SDI failure report to the receiver if it fails to communicate with the D9133 and SERVC SDI 80 displays at the command center. The report to the receiver includes the address of the troubled module to indicate which module needs service.

11.5SDI Address 88

SDI Address 88 is available with the D7212G Panel and is used for several different applications. When using SDI Address 88, only one of the listed devices may be connected at a time.

11.5.1D9133DC Direct Connect Programming Module

The D9133DC Direct Connect Programming Module can be used to locally program the D7212G panel. In addition to this, the D9133DC allows Diagnostics and History retrieval to be performed. The D9133DC is not UL Listed.

11.5.1.1Connecting the D9133DC

1.Configure the D9133DC for SDI Address 88. To program the panel when the reset pin is in the unlocked position, program Enable SDI RAM to Yes in the RADXAUX1 handler.

2.Connect the D9133DC to Com Port 1 or Com Port 2 on the PC. The D9133DC has a DB-9 female serial connector. A null modem cable must be purchased separately to connect the D9133DC to a PC.

3.Using 22 AWG or 18 AWG wire, connect the D9133DC SDI terminals (SDI PWR, SDI A, SDI B, and SDI COM) to the panel’s SDI terminals (Terminals 29 to 32).

To send or receive the panel’s program, the Reset Pin can be in the Locked or Unlocked position.

Note: Locking the Reset Pin when programming the panel improves upload/download time.

11.5.1.2 Used as an External Modem

The D9133DC can also be used as an external modem when using RAM IV with the panel. Please see the D7212G Program Entry Guide (P/N: 4998138538) for programming details.

D7212G Operation and Installation Guide

4998138544C

Page 54

© 2003 Bosch Security Systems

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Control/Communicator D7212G Operation and Installation Guide D7212GContents 10.1 11.111.2 10.0 11.013.0 Figures D7212G Operation and Installation Guide Organization TablesSection Description IntroductionGuide Organization Appendix DescriptionRelated Documentation Documentation ConventionsType Styles Used in the Text FCC Rules Tips, Notes, Cautions and WarningsPart D7212G New Features D9412G D7412G D7212G Overview9000G Series Panel Differences Specifications SecondaryTelephone Connections Telephone Line Ground Fault Detect Features in D7212GCompatible Accessories IntroductionStandard Features Model Display Application Other Features Control/Communicator AssemblyComponents and Literature Available by Separate Order Listings and Approvals BurglaryListings Before Beginning InstallationBeginning the Installation Enclosure OptionsGround Fault Detect Enable Installing the AssemblyConnecting Earth Ground Locking the Reset PinInstall and Wire Detection Devices Finishing the InstallationCharge the Battery While Finishing Install Modules and RelaysInstall the Point Chart Label Testing the SystemProgramming the Panel Power Supply Primary Power TerminalsSecondary Power Terminals Installing the Battery Replacing the BatteryBattery Discharge/Recharge Schedule Battery SupervisionBattery Charging Circuit Float Charge Discharge CycleAction Charging Status and Low Battery LEDsType Color StateAux Power Terminals Continuous Current Draw Power OutputsTotal Available Power Programmable Power Outputs TerminalsFire System Power Formula Relay InstallationAvailable Power Verification/Reset RelayTelephone Connections Phone Line Monitor Operation Monitor LED GreenDialing Format Called Party DisconnectLoop Start Ground StartPhone Monitor Select Jumper Position Ground StartD7212G Point Sensor Loops On-board PointsDescription Terminals Point ParametersBell Off-board Points Point Zonex Bus D7212G TerminalsInstalling the D8125 Popex Module D8125, D8127 and D9127 Popit ModulesLength in ft. m Wiring Data Expansion Loops to Popex ModulesExpansion Loops Combined Popit Sensor LoopsConnecting the D8125 Popex to the D7212G Panel Popit Module Point Assignments Program Record SheetRadxpnts Handler Popit Labels Installing the OctoPOPITD8128D OctoPOPIT Module DescriptionWiring OctoPOPITs Line TerminationD8128D Address Switches Testing Off-board PointsAddress Assignment Switches OctoPOPIT Sensor LoopsConnecting D8128D OctoPOPITs to the D7212G D7212G Panel Relay D8129 OctoRelay D8129 OctoRelay Switch Number Off-board RelaysD8129 OctoRelay D8129 Connections to the D7212G Address Switch Command Center TerminalsAssigning the command center an address Arming DevicesD7212G Command Center Terminal Function Power at Command Centers10.3 D279A Independent Zone Control KeyswitchKeyswitch Operation Maintained Contact Momentary ContactD7212G SDI Devices InstallationPrinter Switch 11.3 D9131A Parallel Printer Interface ModuleSDI Address Address Settings 11.5.2 D9133TTL-E Network Interface ModuleD7212G Accessory Connector Programmer and Accessory ConnectionsProgrammer Connector Programmer Access ReportsAccessoryProgramming ConnectorConnector Programmer and Accessory ConnectionsFaceplate 13.0 13.1 D7212G FaceplateFaceplate Appendix a System Wiring Diagrams, Issue a D7212G Control/Communicator, 1D7212G System Wiring Diagram, 2 D7212G Control/Communicator, 2D7212G System Wiring Diagram, 3 D7212G Control/Communicator, 3D7212G Appendix B Point Address Chart Zonex 1, Points 9 toD7212G Symbols IndexZonex
Top Page Image Contents