SVAT Electronics CLEARVU11 instruction manual Main Menu

Page 32

MAIN MENU

SVAT ELECTRONICS

 

now you can see

The following is a brief description of each item and its specific operations:

•Size (GB) – the total HDD storage in GB (Giga-Byte) for Alarm Record and Normal Record respectively. This item is just for information. Please refer to the section on HDD format/clear for detailed information and setup.

•Auto Overwrite – allows you to automatically overwrite the recorded video/audio from HDD#1 when the Alarm/Normal Record disk drive capacity is full. If Auto Overwrite is disabled and the Alarm/Normal Record disk drive capacity reaches the end, the system will not overwrite the recorded video/audio, and hence not record Alarm/Normal video/audio, until the user presses the Alarm Reset button. Press ENTER or +/- to check/ uncheck this item. The default setting is “” - checked.

•HDD Full Action –Activates certain actions when Alarm/Normal Record disk drive capacity reaches the end of the last HDD. Press ENTER or +/- to check/uncheck this item. The default setting is “” - checked.

•Duration – response duration to define how long (in seconds) the Alarm Out relay and the Buzzer will keep being triggered after the corresponding selection, Alarm Record or Normal Record, is full. Press +/- buttons to adjust the value (3-60 seconds, discrete).

• Alarm Out – to define which Alarm Output will be triggered when the corresponding selection, Alarm Record or Normal Record, is full. Press +/- buttons to select none (N/A) or one of the Alarm Outputs (1-2).

•Buzzer – to activate the internal Buzzer or not when the corresponding partition, Alarm Record or Normal Record, is full. Press ENTER or +/- to check/uncheck this item. The default setting is “” - checked.

•Log – to log to event logs or not. Press ENTER or +/- to check/uncheck this item. The default setting is “” - checked.

•E-mail– to send the event e-mail to a pre-determined email address or not. The e-mail will be sent to the predefined receivers when the event is triggered. Press ENTER or +/- to check/uncheck this item. The default setting is “–” - unchecked.

The general operations are as below:

•▲▼◄►- Press these buttons to select the items.

•MODE - Format/Clear - Press this button to format/clear the HDDs as described in the next section.

•ESC (MENU/ESC) - Press this button to escape from this screen, and return to Setup Menu display. If the Save dialog is shown, press ENTER to exit and save, ESC (MENU/ESC) to exit without saving.

CLEARVU11

29

 

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 4CH 15 LCD-DVR All-In-One System VersionIMPORTANT! Please Read Do not Return this Product to the StoreProduct Warranty Information Table of Contents HDD FORMAT/CLEAR Power Cables IntroductionFor DVR 10ft RJ-45 Cable Software CDButton Functions and Connections Remote Control Infrared IR Sensor Power Cord Inlet Power in For DC-INMonitor Speaker Hard Drive CoverBasic Setup Alpa/Numeric keysAdjust cameras to the desired viewing angles Mounting the CameraPowering the System General Information Main ScreeenGeneral Information Press to move the cursor to the left/rightStop Stops using playback mode Volume Turns muting on or offMenu Used to call up the full menu Search Used to call up the search optionsPTZ Setup Using the Mouse Common IconsPress these buttons to change the highlighted item Enter Main MenuALPHA-NUMERIC Keyboard Press Enter to login the system Enter+/-Press these buttons to adjust the selected item Press these buttons to select the itemsMain Menu PRE-CAMERA Setup Camera Setup TitleCopy Motion Detection Main Menu Covert Call by EventRecord Quality and Record IPS Dwell TimeAudio Alarm Setup Focus Camera the camera corresponding to this alarm inputSEQ Display Setup Following is a brief description of the operations Scheduled Record Setup HDD Setup Main Menu Call Physical Format Mode FormatSEQ Clear Password Setup System Setup System TimeRS-232/422/485 Setup Network Setup Use the keys to navigate over to E-mail or AdvMail Setup Advanced Network Setup Software Upgrade Administrator mode only Factory DefualtsNetworking Guide Connecting Your DVR to the RouterGenuine and fully updated version of Windows XP or Vista Finding the DVR’S IP Address Press ESC to exit out of Menu. Press Enter to save changesPreparing Your Computer for Viewing the DVR Method 1 RecommendedViewing Your DVR on Your Computer MethodNetworking Guide Once YOU are on PORTFORWARD.COM Connecting the DVR Using a D-LINK Router Example Select the Advanced tabSchedule field, select Always Click Apply Finding Your External IP AddressReason to change the DVR to another port not recommended Enter your preferred user name, email address, and password Dynamic DNSNetworking Guide Select Setup Select Network DSL modem is preventing a connectionRemote Viewing Camera Focus windowSearch by Time Search by EventMemory Dram 512MB Setup- Click on this icon to call up Setup dialogSystem Requirements of Remote PC Search Menu Search by TimePlayback/Archive For Search By Time Search Menu Search by Event Search Archived Files Playback/Archive For Search By EventPDA/Mobile Phone Remote Access Playback For Archived FilesHEM Player Keyboard Control Simulator Information Sheet M4V/H.264 to AVI Conversion UtilityTroubleshooting Guide Saved in loginWhen playing back MouseSettings VGA Options is notDVR EtcRemote control is not WorkingSet time IPS to 30 IPSComputer ManualText Cameras My camera is notWhite Electrical noiseSpecifications Alarm SetupNetwork ControlPower ResolutionBattery Operable Viewing Angle ConnectorTV System AutoCLEARVU11 Product Information Quick Start Guides
Top Page Image Contents