New Buck Corporation DV1000 manual Logs, Embers, Burner Pan Assembly, Venting System, Air Shutter

Page 29
LOGS:

LOGS:

If you remove logs for cleaning, refer to Installing Logs, page 18 to properly replace logs.

Use a vacuum cleaner to remove any carbon buildup on logs.

Replace logs if broken. See Replacement Parts on page 29.

Also use a vacuum cleaner to remove any particles on the Burner Pan.

EMBERS:

“Apply loose material per instructions manual. DO NOT apply extra material or material not supplied with the heater. Replace only with material from your Buck Stove dealer or from New Buck Corporation.

BURNER PAN ASSEMBLY

BURNER PAN

BURNER PORTS

Philllips Head Screw

AIR SHUTTER

(To Gain Access To The Air Shutter, Remove The Cover Plate On The Orifice Box Located In The Burner Control Compartment Directly Un- der The Center Of The Burner Pan)

EMBERS: VENTURA ASSEMBLY

Air Shutter Slot (Opening)

VENTING SYSTEM

Periodic examination of venting systems by a qualified agency.

1.Check areas of venting system that are exposed to the weather for corrosion (rust spots or streaks and, in extreme cases, holes). Have these items replaced immediately by a qualified service person.

2.Remove the vent cap and shine a flashlight into the vent. Remove any foreign material.

3.Check for evidence of excessive condensation. Continuous condensation can cause corrosion of caps, pipes, and fittings and can be caused by having excessive lateral runs, too many elbows, or exterior portions of the system being exposed to cold weather.

4.Inspect joints to verify that no pipe section or fitting has been disturbed and loosened. Check me- chanical supports such as wall straps for rigidity.

Page 26

Image 29
Contents Approved By DV1000ZERO CLEARANCE DIRECT VENT GAS FIREPLACE Page TABLE OF CONTENTS Page INSTALLATION AND OPERATION INTRODUCTION AND SAFETY FORDV1000 FIREBOX COVER DOOR REMOVAL INSTRUCTIONS 2. BOTTOM LOUVER ASSEMBLY 1. TOP LOUVER ASSEMBLYLOUVER ASSEMBLY VER ASSEMBLY CLIP TO SECURE TO STOVE BODY38-1/8” 36” 33-1/2” DV1000 SPECIFICATIONS16-15/16” 2-1/2” 6” TOP STANDOFFS SIDE STANDOFFS 27-1/8” 13-9/16”40-1/8” MINIMUM FRAMING DIMENSIONS2-1/2” 36-1/8Page VENT TERMINAL CLEARANCESDETERMINING THE LOCATION FOR DV1000 DV1000 DIRECT VENT TERMINATION INSTALLATION INSTRUCTIONSPIPE INSTALLATION PRE-INSTALLATIONINFORMATIONOUTER 7” VENT PIPE INNER 4” FLUE PIPE FIGURE 8/ OPTIONAL REAR VENT TER CORNER TERMINATION WITH OPTIONAL REAR VENT9-1/2”WALL MINATION EXAMPLEMAXIMUM INSTALLATION MINIMUM INSTALLATIONVERTICAL TERMINATION CAP ASSEMBLY INSTALLATIONSDV1000 STANDARD VERTICAL CHASE TERMINATION 30FT MAXREMOVABLE INNER BOTTOM PAN ASSEMBLY Installation Items Needed INSTALLING GAS PIPING TO APPLIANCEGAS SUPPLY CONNECTION CHECK GAS TYPETest Pressures In Excess of 1/2 PSIG 3.5 kPa Pressure Testing Gas Supply Piping Systemance of the heater DV1000 LOG PLACEMENTWARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury WHAT TO DO IF YOU SMELL GAS FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCE WIRING DIAGRAM REPAIR PARTS SERVICINGCLEANING AND MAINTENANCE VENTURA ASSEMBLY Air Shutter Slot Opening BURNER PAN ASSEMBLYLOGS EMBERSOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYBurner does not light after pilot is lit Diagram, pageMaintenance, page TROUBLESHOOTINGContinued Gas leak. See Warning statementSERVICING REPLACEMENT PARTSKEY# PART DESCRIPTIONPage ON/OFF/MANUALADDITIONAL REPLACEMENT PARTS WARRANTY WARRANTYPROCEDURE CONDITIONS AND EXCLUSIONSOTHER RIGHTS Page