New Buck Corporation DV1000 manual OUTER 7” VENT PIPE INNER 4” FLUE PIPE

Page 14
OUTER 7” VENT PIPE

8.Plan your installation. Set the appliance in place and survey how best to vent the appliance. Se- lect the appropriate termination kit for the installation. Read the vent pipe manufacturers in- structions and the appliance manufacturers instruction manual before either. After vent configu- ration has been decided, stretch the flex components out, then trim off what will not be needed. A temporary fit up will determine this. Once the vent length has been determined and the neces- sary parts are obtained for the installation you can begin installing the venting system.

•Follow the Installation Instructions provided with the Magnaflex DV4-Fventing kit.

CONNECTING OR RECONNECTING THE VENTING SYSTEM TO THE Model DV1000

∗After following the venting manufactures instructions, and you have installed the piping up to the area of the appliance. Continue with the installation using the vent manufactures instruc- tions and the instructions and illustrations in this manual.

A.Add High temperature sealant (caulk) to the inside (inner) edge of the 4” flexible flue pipe.

B.Place the 4” flexible flue pipe through the center of the flex adapter collar w/ gasket , leaving the adapter collar unat- tached to the appliance and pulled up the pipe out of the way. With the 4” clamp also over the 4” flex flue and loose, push the 4” flex flue pipe onto (over) the 4” flue adapter col- lar until it is properly seated (about 1” to 1- 1/4”).

OUTER 7” VENT PIPE

INNER 4” FLUE PIPE

SELF TAPPING SCREWS

FLEX ADAPTER COLLAR WITH GASKET (Gasket may come attach to the collar from the manufacturer)

APPLIANCE 4” FLUE ADAPTOR COLLAR (FLUE EXIT). PRE-

INSTALLED BY THE APPLIANCE MANUFACTURER.

C.Place the 4” clamp over the section of 4” flex flue pipe that is pushed onto the flue adapter and tighten the clamp.

D.Seat the flex flue adapter collar with gasket on to the appliance centering around the flue adapter and secure it to the appliance using (4) four of the self tapping screws provided with the venting kit.

E.Next place the 7” clamp over the end of the 7” flex vent pipe and leave it loose for now.

F.With both hands pull the 7” flex vent pipe onto (over) the flex flue adapter and push it onward until it is properly seated.

G.Place the 7” clamp over the section of 7” flex vent pipe you just seated and tighten.

NOTE: TOP VENT INSTALLATION SHOWN ABOVE. FOL- LOW THE SAME INSTRUCTIONS FOR OPTIONAL REAR VENT INSTALLATION.

FIGURE 7

Page 11

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Approved By DV1000ZERO CLEARANCE DIRECT VENT GAS FIREPLACE Page TABLE OF CONTENTS Page INTRODUCTION AND SAFETY FOR INSTALLATION AND OPERATIONDV1000 FIREBOX COVER DOOR REMOVAL INSTRUCTIONS LOUVER ASSEMBLY 1. TOP LOUVER ASSEMBLY2. BOTTOM LOUVER ASSEMBLY VER ASSEMBLY CLIP TO SECURE TO STOVE BODY16-15/16” 2-1/2” 6” DV1000 SPECIFICATIONS38-1/8” 36” 33-1/2” TOP STANDOFFS SIDE STANDOFFS 27-1/8” 13-9/16”2-1/2” MINIMUM FRAMING DIMENSIONS40-1/8” 36-1/8VENT TERMINAL CLEARANCES PageDETERMINING THE LOCATION FOR DV1000 INSTALLATION INSTRUCTIONS DV1000 DIRECT VENT TERMINATIONPRE-INSTALLATIONINFORMATION PIPE INSTALLATIONOUTER 7” VENT PIPE INNER 4” FLUE PIPE 9-1/2”WALL CORNER TERMINATION WITH OPTIONAL REAR VENTFIGURE 8/ OPTIONAL REAR VENT TER MINATION EXAMPLEMINIMUM INSTALLATION MAXIMUM INSTALLATIONDV1000 STANDARD VERTICAL CHASE TERMINATION INSTALLATIONSVERTICAL TERMINATION CAP ASSEMBLY 30FT MAXREMOVABLE INNER BOTTOM PAN ASSEMBLY GAS SUPPLY CONNECTION INSTALLING GAS PIPING TO APPLIANCEInstallation Items Needed CHECK GAS TYPEPressure Testing Gas Supply Piping System Test Pressures In Excess of 1/2 PSIG 3.5 kPaDV1000 LOG PLACEMENT ance of the heaterWARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury FOR YOUR SAFETY READ BEFORE LIGHTING WHAT TO DO IF YOU SMELL GASLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCE WIRING DIAGRAM SERVICING REPAIR PARTSCLEANING AND MAINTENANCE LOGS BURNER PAN ASSEMBLYVENTURA ASSEMBLY Air Shutter Slot Opening EMBERSPOSSIBLE CAUSE TROUBLESHOOTINGOBSERVED PROBLEM REMEDYDiagram, page Burner does not light after pilot is litContinued TROUBLESHOOTINGMaintenance, page Gas leak. See Warning statementKEY# REPLACEMENT PARTSSERVICING PART DESCRIPTIONON/OFF/MANUAL PageADDITIONAL REPLACEMENT PARTS PROCEDURE WARRANTYWARRANTY CONDITIONS AND EXCLUSIONSOTHER RIGHTS Page
Top Page Image Contents