New Buck Corporation 21 Starter Pipe Seal Trim Panels And Under, Temperature Caulk

Page 9
STARTER PIPE

OPTION (A)

STARTER PIPE

SEAL TRIM PANELS AND UNDER

FRONT OF STOVE UNIT WITH

INSULATION OR HIGH

TEMPERATURE CAULK

NOTE: New Buck Corporation grants no warranty, implied or stated, for the installation or maintenance of your appliance, and assumes no responsibility of any consequential damage

AIRTIGHT INSU-

LATED CLEAN-

OUT

FRONT OF STOVE UNIT WITHTEMPERATURE CAULKAIRTIGHT INSU-OR WIRE IT OPEN(Kit sold separately)Manual backgroundManual backgroundManual background REMOVE

DAMPER

OR WIRE IT OPEN

OPTION (B)

NOTE: Follow installation instruction with Direct Connection Kit.

(Kit sold separately)

SEAL TRIM PANELS

WITH INSULATION

OR HIGH

TEMPERATUREManual backgroundManual backgroundManual backgroundManual backgroundManual background

CAULK

Manual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background STAINLESS

STEEL

CHIMNEY

CONNEC-

TOR MUST

EXTEND 1’

PAST THE

BLOCK-OFF

PLATE OR

TO THE

FLUE LINER

AIRTIGHT

INSULATED

CLEAN-

REMOVE

DAMPER

OR WIRE IT

OPEN

BLOCK-OFF PLATE

OR DAMPER

ADAPTER

OPTION (C)

NOTE: Follow installation instruction with Positive Connection Kit.

(Kit sold separately)

INSTALL A NON-COMBUSTIBLE COVER PLATE TO PREVENT WATER FROM ENTERING THE CHIMNEY

TRIM PANELS

CAP PREVENTS

WATER FROM

ENTERING)

FLUE

LINER

THE LINER MUST

BE STAINLESS

STEEL CONNEC-

TOR OR FLEXIBLE

VENT. FOLLOW

THE LINER MANU-

FACTURER’S IN-

Manual background STRUCTIONS FOR

Manual background INSTALLATION

Manual background AND SUPPORT.

AIRTIGHT

INSULATED

CLEAN-OUT

REMOVE

DAMPER

OR WIRE

IT OPEN

7

Image 9
Contents MODEL NON-CATALYTICUNIT MODEL NON-CATBuck Stove Page TABLE OF CONTENTS INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS MODELREAD THIS FIRST IMPORTANT INSTRUCTIONS INTRODUCTION SECTIONMASONRY INSERT INSTALLATION SECTIONMODEL Floor Protection POSSIBLE TOOLS NEEDED FOR INSTALLATION INSTALLATION PREPARATIONMASONRY INSERT INSTALLATION OPTIONS OR WIRE IT OPEN AIRTIGHT INSU LATED CLEAN OUT REMOVE DAMPERSTARTER PIPE SEAL TRIM PANELS AND UNDER FRONT OF STOVE UNIT WITH INSULATION OR HIGHPOSITIONING POSITIONING THE HEATERMOUNTING THE TRIM PANELS FIGURE 3 MOUNTING TRIM PANELSFINAL CHECK Page SECTION PRE-FABINSERT INSTALLATION Chimney PREPARING THE STOVE FOR INSTALLATIONFloor Protection 1. Convert specification to R-valueResidential Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALLPREPARING THE ROOM HEATER LOCATION CHIMNEYModel 21 minimum clearance to combustibles HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential InstallationNOTE For minimum clearances See Page 17, Figure Model 21 minimum clearance to combustibles HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationWithout close clearance shield and pipe shield NOTE For minimum clearances See Page 19, FigureModel 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE ChimneyHOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationD. Vertical Wall Exit using 6 DVL Close Clearance Pipe, and Elbow, and any Listed 2100 UL HT chimney and Listed 2100 UL HT T-Boxassembly Model 21 minimum clearance to combustibles Listed 2100 UL HT T-BoxassemblyHOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationNOTE For minimum clearances See Page 23, Figure Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE ChimneyHOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationNOTE For minimum clearances See Page 25, Figure Listed 2100 UL HT T-Boxassembly OUT SIDE AIR INSTALLATION Page FINAL CHECK SECTION ALCOVE INSTALLATION AND CLEARANCES PREPARING THE STOVE FOR INSTALLATIONChimney Floor Protection 1. Convert specification to R-valueHOW TO LOCATE CHIMNEY EXIT, AND INSTALL Alcove InstallationALCOVE INSTALLATION AND CLEARANCES any listed 2100 UL 103 HT. TYPE ChimneyModel 21 minimum clearance to combustibles Installation of Optional Pipe Shield Installation of Optional Close Clearance ShieldsPipe Shield Loosen these top shield screws 13/16” TYP 1” TYP 1/4” TYPFINAL CHECK SECTION WOOD HEATER SAFETY BUILDING A FIRE SECTION OPERATIONPROBLEM SECTION TROUBLESHOOTINGSOLUTION POSSIBLE CAUSEPROBLEM SOLUTIONPOSSIBLE CAUSE PROCEDURE WARRANTY TIME PERIODSNEW BUCK CORPORATION NBC PRODUCTS COVEREDOTHER RIGHTS CONDITIONS AND EXCLUSIONS