Heat & Glo LifeStyle SL-750TV-D, SL-950TV-IPI-D, SL-950TV-D Securing and Leveling Appliance

Page 17

C. Securing and Leveling Appliance

WARNING

Fire Risk.

•Prevent contact with sagging, loose insulation.

•Do NOT install against combustible materials

such as exposed insulation, plastic and insulation backer.

The diagram shows how to properly position, level, and secure the appliance (see Figure 7.3). Nailing tabs are pro- vided to secure the appliance to the framing members.

•Place the appliance into position.

•Level the appliance from side to side and front to back.

•Shim the appliance, as necessary. It is acceptable to use wood shims.

•Bend out nailing tabs on each side.

•Keep nailing tabs ﬂush with the framing.

•Secure the appliance to the framing by using nails or screws through the nailing tabs.

Figure 7.3 Proper Positioning, Leveling and Securing of a

Appliance

CAUTION

Do NOT notch into the framing around the appliance spacers.

Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

17

Image 17

Contents What to do if you smell gas Homeowner Reference Information CongratulationsTable of Contents Glass Speciﬁcations 1Listing and Code ApprovalsBTU Speciﬁcations ModelsCombustible Materials Speciﬁcation High Altitude InstallationsNon-Combustible Materials Speciﬁcation Getting Started Design and Installation ConsiderationsNegative Pressure Inspect Appliance and Components Tools and Supplies NeededSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseClearances to Mantels or other Combustibles above Appliance Mantel ProjectionsVent Termination Minimum Clearances Termination LocationsVent System Conﬁguration Vent Information and DiagramsVent Guidelines Minimum Vertical Feet Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Gas and Electrical Connections Installing Outside Air Kit Damper AssemblyAppliance Preparation Proper Positioning, Leveling and Securing of a Securing and Leveling ApplianceAssembly of Vent Sections Installing Vent PipeSecuring Vent Sections Attaching Vent to FireboxFuel Conversions Gas Connection Gas InformationGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Connecting to the Appliance Recommendation for WireIntelliﬁre Ignition System Wiring Optional Accessories RequirementsGround to Standing Pilot Ignition System WiringWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingClean the Appliance Appliance SetupAccessories Remove Shipping MaterialsPositioning the Logs Log Set Assembly LOGS-SL550-D Models SL-550TV-DTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Shutter Settings Glass AssemblyScreen Mesh Grilles and TrimBefore Lighting Appliance Operating InstructionsCheck Appliance Draft Before operating this appliance have a qualified technicianIntelliﬁre Ignition Lighting ApplianceStanding Pilot Ignition For Your Safety Read Before Lighting InstructionsAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Actions Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Symptom Possible Causes Corrective Actions Before servicing Maintaining and Servicing ApplianceInspect Maintenance Tasks Reference Materials Appliance Dimension DiagramAppliance Dimensions Table Log Set Assembly Service PartsSL-550TV-D Service Parts ListSL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyDo not Discard this Manual Contact Information