Heat & Glo LifeStyle SL-950TV-D Appliance Setup, Remove Shipping Materials, Clean the Appliance

Page 25

12 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the ﬁrebox.

B. Remove Grate Shipping Support

•Remove the log pack and hood, if applicable.

•Bend top retaining tab of grate shipping support into vertical position (see Figure 12.1).

•Lift grate slightly upward with one hand so that the grate clears the support.

•Slide shipping support to side, remove and discard.

•Lower grate onto refractory.

Figure 12.1

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the ﬁrebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate acces- sories. Refer to Section 16.

WARNING

Shock or ﬁre risk.

Use ONLY optional accessories approved for this appliance.

•Using non-listed accessories voids warranty.

•Using non-listed accessories may result in a safety hazard.

•Only Hearth & Home Technologies approved accessories may be used safely.

E.Install the Refractory

F.Lava Rock, Vermiculite, Rockwool/ Ember Placement

WARNING

Explosion Risk.

•Follow ember placement instructions in manual.

•Do NOT place embers directly over burner ports.

•Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

Placing the Ember Material

Ember material is shipped with this gas appliance. To place the ember material:

•When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place the dime-size ember pieces about 1/2 inch apart near port holes in burner top, but not on or in between the ports. For best performance do NOT place embers on ports at rear of burner (see Figure 12.2). Failure to follow this procedure will likely cause lighting and sooting problems.

•Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

Figure 12.2 Placement of Embers

Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

25

Image 25

Contents What to do if you smell gas Homeowner Reference Information CongratulationsTable of Contents Glass Speciﬁcations 1Listing and Code ApprovalsBTU Speciﬁcations ModelsNon-Combustible Materials Speciﬁcation High Altitude InstallationsCombustible Materials Speciﬁcation Getting Started Design and Installation ConsiderationsNegative Pressure Inspect Appliance and Components Tools and Supplies NeededSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseClearances to Mantels or other Combustibles above Appliance Mantel ProjectionsVent Termination Minimum Clearances Termination LocationsVent Guidelines Vent Information and DiagramsVent System Conﬁguration Minimum Vertical Feet Pipe Clearances to Combustibles Vent Clearances and FramingVertical Penetration Framing Appliance Preparation Installing Outside Air Kit Damper AssemblyGas and Electrical Connections Proper Positioning, Leveling and Securing of a Securing and Leveling ApplianceAssembly of Vent Sections Installing Vent PipeSecuring Vent Sections Attaching Vent to FireboxFuel Conversions Gas Connection Gas InformationGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Connecting to the Appliance Recommendation for WireIntelliﬁre Ignition System Wiring Optional Accessories RequirementsGround to Standing Pilot Ignition System WiringWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingClean the Appliance Appliance SetupAccessories Remove Shipping MaterialsPositioning the Logs Log Set Assembly LOGS-SL550-D Models SL-550TV-DTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Shutter Settings Glass AssemblyScreen Mesh Grilles and TrimBefore Lighting Appliance Operating InstructionsCheck Appliance Draft Before operating this appliance have a qualified technicianIntelliﬁre Ignition Lighting ApplianceStanding Pilot Ignition For Your Safety Read Before Lighting InstructionsInitial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Symptom Possible Causes Corrective Actions TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Symptom Possible Causes Corrective Actions Before servicing Maintaining and Servicing ApplianceInspect Maintenance Tasks Appliance Dimensions Table Appliance Dimension DiagramReference Materials Log Set Assembly Service PartsSL-550TV-D Service Parts ListSL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyDo not Discard this Manual Contact Information