Heat & Glo LifeStyle SL-750TV-IPI-D Tools and Supplies Needed, Inspect Appliance and Components

Page 8

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Reciprocating saw

Framing material

Pliers

Hi temp caulking material

Hammer

Gloves

Phillips screwdriver

Framing square

Flat blade screwdriver

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Tape measure

Manometer

Voltmeter

Non-corrosive leak check solution

1/2 - 3/4 inch length, #6 or #8 Self-drilling screws One 1/4 inch female connection (for optional fan).

D. Inspect Appliance and Components

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components.

Report suspected damaged parts to dealer.

The following B-vent components are needed for installa- tion (see Figure 2.2).

Fireplace Box

Pipe Components

Firestops

Attic Insulation Shield

Elbows

Strapping

Roof Flashing or Chase Top

Termination Cap

Storm Collar

Carefully remove the appliance and components from the packaging.

The vent system components and trim doors are shipped in separate packages.

The gas logs may be packaged separately and must be field installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

VERTICAL TERMINATION CAP

STORM COLLAR

ROOF FLASHING

OR CHASE TOP

ATTIC INSULATION SHIELD

FIRESTOP SPACER

GAS B-VENT

PIPE SECTION (S)

Figure 2.2 Typical Vertical Installation

Read all of the instructions before starting the instal- lation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

8

Heat & Glo • SL-550 / 750 / 950TV-D2053-985 Rev. J • 4/07

Image 8
Contents What to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents 1Listing and Code Approvals Glass SpecificationsBTU Specifications ModelsCombustible Materials Specification High Altitude InstallationsNon-Combustible Materials Specification Design and Installation Considerations Getting StartedNegative Pressure Tools and Supplies Needed Inspect Appliance and ComponentsFraming and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesMantel Projections Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent System Configuration Vent Information and DiagramsVent Guidelines Minimum Vertical Feet Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Gas and Electrical Connections Installing Outside Air Kit Damper AssemblyAppliance Preparation Securing and Leveling Appliance Proper Positioning, Leveling and Securing of aInstalling Vent Pipe Assembly of Vent SectionsSecuring Vent Sections Attaching Vent to FireboxGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Connecting to the ApplianceIntellifire Ignition System Wiring Optional Accessories RequirementsStanding Pilot Ignition System Wiring Ground toJunction Box Installation Wall Switch Installation for Fan OptionalFinishing Facing MaterialAppliance Setup Clean the ApplianceAccessories Remove Shipping MaterialsLog Set Assembly LOGS-SL550-D Models SL-550TV-D Positioning the LogsTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Glass Assembly Shutter SettingsScreen Mesh Grilles and TrimOperating Instructions Before Lighting ApplianceCheck Appliance Draft Before operating this appliance have a qualified technicianLighting Appliance Intellifire IgnitionFor Your Safety Read Before Lighting Instructions Standing Pilot IgnitionAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Actions Troubleshooting Symptom Possible Cause Corrective ActionIntellifire Ignition System Symptom Possible Causes Corrective Actions Maintaining and Servicing Appliance Before servicingInspect Maintenance Tasks Reference Materials Appliance Dimension DiagramAppliance Dimensions Table Service Parts Log Set AssemblyService Parts List SL-550TV-DSL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Do not Discard this Manual