Heat & Glo LifeStyle SL-750TV-IPI-D, SL-950TV-IPI-D, SL-950TV-D, SL-550TV-D Minimum Vertical Feet

Page 14

WARNING

Fire Risk. Explosion Risk.

Insulation and other combustibles must not infringe on clearances.

• ALWAYS maintain speciﬁed clearances around venting and ﬁrestop systems.

• Install ﬁrestops as speciﬁed.

Failure to keep insulation or other material away from vent pipe may cause ﬁre.

MAXIMUM HORIZONTAL 15 FEET

MINIMUM

VERTICAL

9 FEET

45 DEGREES	OFFSETS EXCEEDING
ELBOW	45 DEGREES ADAPT
	HORIZONTAL LIMITATIONS

90DEGREES ELBOW

Note: Maximum horizontal distance is 50% vertical vent height.

Figure 5.3

14	Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

Image 14

Contents What to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents BTU Speciﬁcations 1Listing and Code ApprovalsGlass Speciﬁcations ModelsCombustible Materials Speciﬁcation High Altitude InstallationsNon-Combustible Materials Speciﬁcation Design and Installation Considerations Getting StartedNegative Pressure Tools and Supplies Needed Inspect Appliance and ComponentsFraming and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesMantel Projections Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent System Conﬁguration Vent Information and DiagramsVent Guidelines Minimum Vertical Feet Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Gas and Electrical Connections Installing Outside Air Kit Damper AssemblyAppliance Preparation Securing and Leveling Appliance Proper Positioning, Leveling and Securing of aSecuring Vent Sections Installing Vent PipeAssembly of Vent Sections Attaching Vent to FireboxGas Pressures Gas InformationFuel Conversions Gas Connection Pressure Natural Gas PropaneHigh Altitude Installations Intelliﬁre Ignition System Wiring Recommendation for WireConnecting to the Appliance Optional Accessories RequirementsStanding Pilot Ignition System Wiring Ground toJunction Box Installation Wall Switch Installation for Fan OptionalFinishing Facing MaterialAccessories Appliance SetupClean the Appliance Remove Shipping MaterialsLog Set Assembly LOGS-SL550-D Models SL-550TV-D Positioning the LogsTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Screen Mesh Glass AssemblyShutter Settings Grilles and TrimCheck Appliance Draft Operating InstructionsBefore Lighting Appliance Before operating this appliance have a qualified technicianLighting Appliance Intelliﬁre IgnitionFor Your Safety Read Before Lighting Instructions Standing Pilot IgnitionAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Actions Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Symptom Possible Causes Corrective Actions Maintaining and Servicing Appliance Before servicingInspect Maintenance Tasks Reference Materials Appliance Dimension DiagramAppliance Dimensions Table Service Parts Log Set AssemblyService Parts List SL-550TV-DSL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Do not Discard this Manual