Heat & Glo LifeStyle SL-750TV-IPI-D, SL-950TV-IPI-D, SL-950TV-D, SL-550TV-D Positioning the Logs

Page 26

G. Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

Log Set Assembly: LOGS-SL550-D

Models: SL-550TV-D

Carefully remove the logs from the packaging. CAUTION: Logs are fragile!

2 4

1 3 5

NOTCHES

TABS

METAL TABS

1

LOG #1 (SRV2044-700):Place log #1 onto the grate bars so that the notches in the bottom of the log ﬁt onto the grate bars. Slide the log to the front tab for NG, slide to the rear tab for LP.

NOTCH

2

LOG #2 (SRV550-717):Place log #2 on the right two grate bars using the notch on the bottom of log #2. Slide the right edge of log #2 forward until it touches the grate.

26	Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

Image 26

Contents What to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents BTU Speciﬁcations 1Listing and Code ApprovalsGlass Speciﬁcations ModelsCombustible Materials Speciﬁcation High Altitude InstallationsNon-Combustible Materials Speciﬁcation Design and Installation Considerations Getting StartedNegative Pressure Tools and Supplies Needed Inspect Appliance and ComponentsFraming and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesMantel Projections Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent System Conﬁguration Vent Information and DiagramsVent Guidelines Minimum Vertical Feet Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Gas and Electrical Connections Installing Outside Air Kit Damper AssemblyAppliance Preparation Securing and Leveling Appliance Proper Positioning, Leveling and Securing of aSecuring Vent Sections Installing Vent PipeAssembly of Vent Sections Attaching Vent to FireboxGas Pressures Gas InformationFuel Conversions Gas Connection Pressure Natural Gas PropaneHigh Altitude Installations Intelliﬁre Ignition System Wiring Recommendation for WireConnecting to the Appliance Optional Accessories RequirementsStanding Pilot Ignition System Wiring Ground toJunction Box Installation Wall Switch Installation for Fan OptionalFinishing Facing MaterialAccessories Appliance SetupClean the Appliance Remove Shipping MaterialsLog Set Assembly LOGS-SL550-D Models SL-550TV-D Positioning the LogsTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Screen Mesh Glass AssemblyShutter Settings Grilles and TrimCheck Appliance Draft Operating InstructionsBefore Lighting Appliance Before operating this appliance have a qualified technicianLighting Appliance Intelliﬁre IgnitionFor Your Safety Read Before Lighting Instructions Standing Pilot IgnitionAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Actions Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Symptom Possible Causes Corrective Actions Maintaining and Servicing Appliance Before servicingInspect Maintenance Tasks Reference Materials Appliance Dimension DiagramAppliance Dimensions Table Service Parts Log Set AssemblyService Parts List SL-550TV-DSL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Do not Discard this Manual