Heat & Glo LifeStyle SL-550TV-D Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D

Page 28

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

2 4 6

1

3 5

Log Set Assembly: LOGS-SL750-D

Models: SL-750TV-D, SL-950TV-D

Carefully remove the logs from the packaging. CAUTION: Logs are fragile!

NOTCHES

METAL TABS

1

LOG #1 (SRV2045-700):Place log #1 on the grate using the notches in the bottom of the log. Slide log #1 up to the front tabs for NG. Slide it back until top of log touches the back of the ﬁreplace for LP.

NOTCHES

2

LOG #2 (SRV530-719):Place log #2 on the right two grate bars using the notches in the bottom of the log. Slide the log backward until the back edge is in contact with the tab and parallel to log #1.

28	Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

Image 28

Contents What to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents 1Listing and Code Approvals Glass SpeciﬁcationsBTU Speciﬁcations ModelsNon-Combustible Materials Speciﬁcation High Altitude InstallationsCombustible Materials Speciﬁcation Design and Installation Considerations Getting StartedNegative Pressure Tools and Supplies Needed Inspect Appliance and ComponentsFraming and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesMantel Projections Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Guidelines Vent Information and DiagramsVent System Conﬁguration Minimum Vertical Feet Pipe Clearances to Combustibles Vent Clearances and FramingVertical Penetration Framing Appliance Preparation Installing Outside Air Kit Damper AssemblyGas and Electrical Connections Securing and Leveling Appliance Proper Positioning, Leveling and Securing of aInstalling Vent Pipe Assembly of Vent SectionsSecuring Vent Sections Attaching Vent to FireboxGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Connecting to the ApplianceIntelliﬁre Ignition System Wiring Optional Accessories RequirementsStanding Pilot Ignition System Wiring Ground toJunction Box Installation Wall Switch Installation for Fan OptionalFinishing Facing MaterialAppliance Setup Clean the ApplianceAccessories Remove Shipping MaterialsLog Set Assembly LOGS-SL550-D Models SL-550TV-D Positioning the LogsTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Glass Assembly Shutter SettingsScreen Mesh Grilles and TrimOperating Instructions Before Lighting ApplianceCheck Appliance Draft Before operating this appliance have a qualified technicianLighting Appliance Intelliﬁre IgnitionFor Your Safety Read Before Lighting Instructions Standing Pilot IgnitionInitial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Symptom Possible Causes Corrective Actions TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Symptom Possible Causes Corrective Actions Maintaining and Servicing Appliance Before servicingInspect Maintenance Tasks Appliance Dimensions Table Appliance Dimension DiagramReference Materials Service Parts Log Set AssemblyService Parts List SL-550TV-DSL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Do not Discard this Manual