Heat & Glo LifeStyle SL-550TV-IPI-D, SL-950TV-IPI-D, SL-950TV-D, SL-750TV-IPI-D TAB Locator

Page 27

NOTCH

3

LOG #3 (SRV2044-703):Place log #3 on the left two grate bars using the notch on the bottom of log #3. Slide the left edge of log #3 forward until it touches the grate.

TAB LOCATOR

4

LOG #4 (SRV2044-701):Place log #4 into the tab on log #1. The bottom notch of log #4 should sit on the grate as shown.

TAB LOCATOR

5

LOG #5 (SRV2044-702):Place log #5 into the tab in log #1. The “Y” end of log #6 should ﬁt around the grate as shown.

Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

27

Image 27

Contents What to do if you smell gas Homeowner Reference Information CongratulationsTable of Contents Models 1Listing and Code ApprovalsGlass Speciﬁcations BTU SpeciﬁcationsHigh Altitude Installations Non-Combustible Materials SpeciﬁcationCombustible Materials Speciﬁcation Getting Started Design and Installation ConsiderationsNegative Pressure Inspect Appliance and Components Tools and Supplies NeededSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseClearances to Mantels or other Combustibles above Appliance Mantel ProjectionsVent Termination Minimum Clearances Termination LocationsVent Information and Diagrams Vent GuidelinesVent System Conﬁguration Minimum Vertical Feet Vent Clearances and Framing Pipe Clearances to CombustiblesVertical Penetration Framing Installing Outside Air Kit Damper Assembly Appliance PreparationGas and Electrical Connections Proper Positioning, Leveling and Securing of a Securing and Leveling ApplianceAttaching Vent to Firebox Installing Vent PipeAssembly of Vent Sections Securing Vent SectionsPressure Natural Gas Propane Gas InformationFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations Optional Accessories Requirements Recommendation for WireConnecting to the Appliance Intelliﬁre Ignition System WiringGround to Standing Pilot Ignition System WiringWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingRemove Shipping Materials Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Set Assembly LOGS-SL550-D Models SL-550TV-DTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Grilles and Trim Glass AssemblyShutter Settings Screen MeshBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance Check Appliance DraftIntelliﬁre Ignition Lighting ApplianceStanding Pilot Ignition For Your Safety Read Before Lighting InstructionsFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Causes Corrective ActionsStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Symptom Possible Causes Corrective Actions Before servicing Maintaining and Servicing ApplianceInspect Maintenance Tasks Appliance Dimension Diagram Appliance Dimensions TableReference Materials Log Set Assembly Service PartsSL-550TV-D Service Parts ListSL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyDo not Discard this Manual Contact Information