CarAlarms.com P90-NG1 Glass Door Installation, Arch Surround, Optional Screen Door, Screw Bracket

Page 31

INSTALLATION

GLASS DOOR

INSTALLATION

1)Fit top door bracket over the fl ange at the top of the fi rebox.

2)Secure with 2 screws on the bottom.

Flange

Door

ARCH SURROUND

1)Place the Arch Surround into position by sliding the 2 holes in the bottom brackets over the pins on the base.

Fit the bottom brackets over

the pins on the base.

2)Slide the 2 screws on the rear of the Arch Surround into the bracket on the Glass Door and then tighten screw to secure.

Screw

Bracket

View from underneath of the

screw and the bracket.

Tighten both screws to secure Arch Surround

to Glass Door.

3)Slide Bottom Louver into position. On each side secure the bottom screw fi rst into the side bracket. Do not overtighten, leave slightly loose to allow the louver to move freely. Then tighten the top screw.

Bottom

Screw

Top

Screw

4)Attach the two control boxes to the bottom unit base and tighten the 2 screws on the left side and 1 screw on the right side.

Secure left side with 2 screws and right side

with one screw.

OPTIONAL

SCREEN DOOR

1)Attach door bracket to side using 2 screws.

Door Bracket attaches with 2 screws.

Single Screen Door - only attach to right side of unit.

Double Screen Door - attach to left and right side of unit.

2) Slide the door(s) onto the hinges.

3)SingleScreenDooronly:PushtheLocking BallPinintotheholeontheleftside.Squeeze the clamp (use pliers) and slide it over the end of the Locking Ball Pin and tight against the Facade edge.

Excalibur® P90 Zero Clearance Direct Vent Gas Fireplace

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 07/17/06 P90 Zero Clearance Direct Vent Gas FireplaceTo the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Copy of Safety Decal for P90 Safety LabelFor the State of Massachusetts only RequirementsImportant Message Save These Instructions InstallationGeneral Safety Information Installation ChecklistOptional Heat Release KIT Locating Your GAS FireplaceManufactured Mobile Home Additional Requirements HeatwaveUnit Base STAND-OFFS Framing DimensionsCombustible Mantels Framing FinishingFacing Over 1 25mm Thick Facing RequirementFloor Mounted Fireplaces Raised Fireplaces Side Nailing Strips Unit Assembly Prior to InstallationTop Standoff Assembly Venting IntroductionFPI Direct Vent System Flex Horizontal Terminations Only VentingExterior Vent Termination Locations SV4LB6 Rigid Pipe Venting Components ListCaps Rigid Pipe Venting SystemsAlternate HorizontalHorizontal & Vertical Terminations for 5 x 8 Venting 8 outer diameter Rigid Pipe Venting Arrangements Horizontal TerminationsRigid Pipe Venting Arrangements Vertical Terminations Installation Option + V1 H + H1 Horizontal Venting with Two 2 90o ElbowsHorizontal Venting with Three 3 90o Elbows Option + H1Vertical Venting with Three 3 90o Elbows Vertical Venting with Two 2 90o ElbowsOption Diagram Below Grade InstallationHorizontal Terminations Vertical Terminations This allows for small adjustmentsOffset Chart Installation ProceduresFor FPI Direct Vent System Flex High Elevation Pilot AdjustmentGAS Line Installation GAS Pipe Pressure TestingLPG Conversion Kit Contains Qty Description Conversion KIT #791-969 from NG to LPInstallation of the DC Sparker for the H35-1 Units Only Installation of the DC Sparker For the P90 Units Only Ground Wire from Kit 02-53 02-75 02-54 02-52 02-50 02-53 02-51Bracket 2nd Grate TabPlace embers in these 3 locations On the burner tray 02-5302-5102-50 02-53 Front BracketsScrew Bracket Glass Door InstallationArch Surround Optional Screen DoorDouble & Single Door Option Accent KIT InstallationWall Thermostat Remote ControlWall Switch Thermostat Wire TableDo not cut the ground terminal off under any circumstances Wiring DiagramsFor Propane Units and Units Equipped with DC Spark Boxes Operating Instructions Normal Operating Sounds of GAS Appliances Copy of the Lighting Plate InstructionsMaintenance To Remove the Fan FAN MaintenanceTo Install the Fan Shut the power offImpossible Installing ValveRemoving Valve HintP90 Main Assembly Parts ListDescription Heat Wave Duct KIT P90 Burner Assembly & LOG SET Description P90 Flush Front AccessoriesExcalibur P90 Zero Clearance Direct Vent Gas Fireplace Excalibur P90 Zero Clearance Direct Vent Gas Fireplace Warranty Limited Lifetime WarrantyInstaller Please complete the following information

P90-NG1 specifications

CarAlarms.com P90-NG1 is a cutting-edge vehicle security system designed to provide maximum protection against theft and unauthorized access. This advanced system combines innovative technology with user-friendly features to ensure that car owners can safeguard their vehicles effectively.

One of the standout features of the P90-NG1 is its two-way communication system. This allows users to receive real-time alerts and notifications directly on their key fob whenever the system detects any suspicious activity. The LCD display on the key fob provides clear information, including the vehicle's status, which enhances the overall user experience. This feature ensures that users are always informed about their vehicle’s security status, whether they are close by or a significant distance away.

The P90-NG1 also employs a state-of-the-art shock sensor, which detects impacts on the vehicle's body. This allows the system to respond swiftly to attempted break-ins or vandalism, triggering an audible alarm to deter potential thieves. The adjustable sensitivity of the shock sensor can be customized to suit different environments, ensuring that users can find an optimal balance between security and everyday usability.

Another notable characteristic of the P90-NG1 is its remote start capability. This feature enables users to start their vehicle from afar, adding convenience, especially in harsh weather conditions. Paired with the optional smartphone app, users can control their vehicle’s security functions from their mobile devices, providing added flexibility and peace of mind.

The installation process of the P90-NG1 is designed to be straightforward and efficient, making it suitable for a wide range of vehicles. The system is compatible with various vehicle models and can be integrated seamlessly with existing systems, providing enhanced functionality without compromising factory features.

In conclusion, CarAlarms.com P90-NG1 stands out in the vehicle security market due to its robust features, advanced technology, and user-centric design. With its reliable two-way communication, effective shock sensor, and convenient remote start capability, it offers vehicle owners a comprehensive solution to protect their assets while ensuring ease of use. This makes the P90-NG1 an ideal choice for those looking to enhance the security of their vehicles.
Top Page Image Contents