CarAlarms.com P90-NG1 manual Conversion KIT #791-969 from NG to LP

Page 25

INSTALLATION

CONVERSION KIT #791-969 FROM NG TO LP

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!

Each Kit contains one LPG Conversion Kit and one DC Sparker Kit.

LPG Conversion Kit Contains:

Qty. Part #

Description

1

904-529

5/32" Allen Key

1

904-645

Burner Orifi ce #51

1918-590 Label "Converted to LPG"

1

908-528

Red "LPG" label

1

910-037

LP Injector (Pilot Orifi ce)

1

918-487

Instruction Sheet

DC Sparker Kit Contains:

Qty. Part #

Description

1

820-475

Bracket DC Sparker

1

820-476

Bracket DC Sparker

1

904-153

Washer #8 External Star

1

904-330

Nut 8-32 Hex

1904-438 Plug Nylon 0.750 Hole, Black

1904-531 Bushing Split Plastic

0.500 in.

1904-543 Screw 8-32 x 3/4 Pan Head

2904-553 Screw #8 x 1/2 Type "B",

Black Oxide

1

910-073

Spark Generator Battery

 

 

Holder

1910-074 Spark Generator Switch C/W Wire

1910-078 Battery Size AA Energizer En91

2910-199 Clip Wire Holder

1910-903 Wire Fan To Power Cord Ground 30 in.

904-781 Velcro Hook, Black

904-782 Velcro Hook, Black

Installation of LPG

Conversion Kit:

1)Shut off the gas supply.

2)H35-1:Lift off the Cast Top and remove the glass front. Also, open up the control panel door.

P90-1:Remove the facade if it is in- stalled. Remove the glass door (refer to the glass door section in the manual).

3)Remove the logs, embers, and brick panels (if used).

4)Remove the 2 screws holding the Burner Assembly to the fi rebox base. Push the Burner Assembly to the left and lift out.

Remove the 2 screws, push Burner

Assembly to the left and lift out.

5)Pull off the pilot cap to expose the pilot orifi ce.

6)Unscrew the pilot orifi ce with the allen key and replace with the LP pilot orifi ce in the kit and replace pilot cap.

7)Remove burner orifi ce with a 1/2" wrench and discard. Use another wrench to hold on to the elbow behind the orifi ce.

Burner Orifi ce

8)Reinstall new burner orifi ce LP stamped #51 and tighten.

9) Turn control knob to the “OFF” position.

10) Remove the black protection cap by hand from the high-low knob (Fig.1).

Fig. 1

11) Insert a 5/32” or 4mm Allen wrench into the hexagonal key-way of the screw (Fig. 2), rotate it counter- clockwise until it is free and extract it.

Fig.2

12) Check that the screw is clean and if necessary remove dirt.

13) Flip the screw (Fig. 3).

Fig.3

Excalibur® P90 Zero Clearance Direct Vent Gas Fireplace

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 07/17/06 P90 Zero Clearance Direct Vent Gas FireplaceTo the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Copy of Safety Decal for P90 Safety LabelFor the State of Massachusetts only RequirementsGeneral Safety Information InstallationInstallation Checklist Important Message Save These InstructionsManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceHeatwave Optional Heat Release KITCombustible Mantels Framing DimensionsFraming Finishing Unit Base STAND-OFFSFacing Over 1 25mm Thick Facing RequirementFloor Mounted Fireplaces Raised Fireplaces Top Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Side Nailing StripsFPI Direct Vent System Flex Horizontal Terminations Only VentingExterior Vent Termination Locations SV4LB6 Rigid Pipe Venting Components ListAlternate Rigid Pipe Venting SystemsHorizontal CapsHorizontal & Vertical Terminations for 5 x 8 Venting 8 outer diameter Rigid Pipe Venting Arrangements Horizontal TerminationsRigid Pipe Venting Arrangements Vertical Terminations Installation Horizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsOption + H1 Option + V1 H + H1Vertical Venting with Three 3 90o Elbows Vertical Venting with Two 2 90o ElbowsOption Diagram Below Grade InstallationHorizontal Terminations Vertical Terminations This allows for small adjustmentsOffset Chart Installation ProceduresFor FPI Direct Vent System Flex GAS Line Installation Pilot AdjustmentGAS Pipe Pressure Testing High ElevationLPG Conversion Kit Contains Qty Description Conversion KIT #791-969 from NG to LPInstallation of the DC Sparker for the H35-1 Units Only Installation of the DC Sparker For the P90 Units Only Ground Wire from Kit Bracket 02-75 02-54 02-52 02-50 02-53 02-512nd Grate Tab 02-5302-50 02-53 02-5302-51Front Brackets Place embers in these 3 locations On the burner trayArch Surround Glass Door InstallationOptional Screen Door Screw BracketDouble & Single Door Option Accent KIT InstallationWall Switch Remote ControlThermostat Wire Table Wall ThermostatDo not cut the ground terminal off under any circumstances Wiring DiagramsFor Propane Units and Units Equipped with DC Spark Boxes Operating Instructions Normal Operating Sounds of GAS Appliances Copy of the Lighting Plate InstructionsMaintenance To Install the Fan FAN MaintenanceShut the power off To Remove the FanRemoving Valve Installing ValveHint ImpossibleP90 Main Assembly Parts ListDescription Heat Wave Duct KIT P90 Burner Assembly & LOG SET Description P90 Flush Front AccessoriesExcalibur P90 Zero Clearance Direct Vent Gas Fireplace Excalibur P90 Zero Clearance Direct Vent Gas Fireplace Warranty Limited Lifetime WarrantyInstaller Please complete the following information

P90-NG1 specifications

CarAlarms.com P90-NG1 is a cutting-edge vehicle security system designed to provide maximum protection against theft and unauthorized access. This advanced system combines innovative technology with user-friendly features to ensure that car owners can safeguard their vehicles effectively.

One of the standout features of the P90-NG1 is its two-way communication system. This allows users to receive real-time alerts and notifications directly on their key fob whenever the system detects any suspicious activity. The LCD display on the key fob provides clear information, including the vehicle's status, which enhances the overall user experience. This feature ensures that users are always informed about their vehicle’s security status, whether they are close by or a significant distance away.

The P90-NG1 also employs a state-of-the-art shock sensor, which detects impacts on the vehicle's body. This allows the system to respond swiftly to attempted break-ins or vandalism, triggering an audible alarm to deter potential thieves. The adjustable sensitivity of the shock sensor can be customized to suit different environments, ensuring that users can find an optimal balance between security and everyday usability.

Another notable characteristic of the P90-NG1 is its remote start capability. This feature enables users to start their vehicle from afar, adding convenience, especially in harsh weather conditions. Paired with the optional smartphone app, users can control their vehicle’s security functions from their mobile devices, providing added flexibility and peace of mind.

The installation process of the P90-NG1 is designed to be straightforward and efficient, making it suitable for a wide range of vehicles. The system is compatible with various vehicle models and can be integrated seamlessly with existing systems, providing enhanced functionality without compromising factory features.

In conclusion, CarAlarms.com P90-NG1 stands out in the vehicle security market due to its robust features, advanced technology, and user-centric design. With its reliable two-way communication, effective shock sensor, and convenient remote start capability, it offers vehicle owners a comprehensive solution to protect their assets while ensuring ease of use. This makes the P90-NG1 an ideal choice for those looking to enhance the security of their vehicles.
Top Page Image Contents