Nilfisk-ALTO SW 750 Machine Operation, Hopper Emptying, After Machine USE, First Period of USE

Page 49

USER MANUAL

ENGLISH

MACHINE OPERATION

1.Avoid stopping for a long time with the machine in the same position and the brooms rotating: this could create unwanted marks on the fl oor.

2.For machine proper operation, the dust fi lter must be as clean as possible. Therefore the fi lter shaker must be used at regular intervals (every 10 minutes, but this interval may vary according to the fl oor conditions), according to the following procedure.

•Stop the machine and turn the main switch (1) to "0".

•To shake the fi lter, move the fi lter shaker knob (8) to the right and then to the left several times.

•Turn the main switch (1) to “I” or to "II" and start sweeping again.

NOTE

When the dust fi lter is clogged, the machine cannot collect dust and debris anymore.

CAUTION!

Do not work on wet floors to prevent the dust filter from being damaged.

3.The hopper (9) should be emptied after each working cycle and whenever it is full.

NOTE

When the hopper is full, the machine cannot collect dust and debris anymore.

HOPPER EMPTYING

Stop the machine and turn the main switch (1) to "0".

Remove the hopper (9) by using the handles (31) and (32), then empty it at the waste collection centre. Then install the hopper.

The machine is ready to start working again.

NOTE

When the hopper is removed, all machine functions are disabled.

AFTER MACHINE USE

After working, before leaving the machine:

1.Turn the main switch (1) to "0".

2.Turn on the fi lter shaker with the knob (8).

3.Empty the hopper (9) (see the procedure in the previous paragraph).

4.Lift the side broom (11) by pulling the lever (12) backwards and by engaging it to the fastener.

5.Make sure that the machine cannot move independently.

6.Charge the batteries (see the procedure in the Maintenance chapter).

MACHINE LONG INACTIVITY

If the machine is not going to be used for more than 30 days, proceed as follows:

1.Perform the daily maintenance procedures (see the Maintenance chapter).

2.Check that the machine storage area is dry and clean.

3.Slightly lift the machine so that the skirts, the main broom and the wheels do not touch the ground.

FIRST PERIOD OF USE

After the fi rst 8 hours, check the machine fastening and connecting parts for proper tightening and check the visible parts for integrity and leakage.

SW 750

146 3080 000(1)2006-10 A

11

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Deutsch Français English Nederlands Sweeper Einleitung InhaltsverzeichnisEinleitung AUSPACKEN/AUSLIEFERUNG Sicherheit Benutzte SymboleAllgemeine Hinweise Betriebsanleitung Deutsch Struktur UND Bedienelemente DER Maschine MaschinenbeschreibungStruktur UND Bedienelemente DER Maschine Beschreibung Technische Daten ZUBEHÖRE/OPTIONENAllgemein Werte Elektrische Teile WerteFarbencodes SchaltplanPrüfung DER Batterien AN Einer Neuen Maschine BetriebVOR DEM Anlassen DER Maschine Maschinenanlassen UND -ABSTELLENEntleerung DES Abfallbehälters Maschine in BetriebNach DER Maschinenbenutzung Lange Ausserdienststellung DER MaschineÜbersichtstabelle DER Planmässigen Wartung WartungPrüfung DES Ladegerätkabels Vorgang AlleAUSBAU/EINBAU DES Seitenbesens Prüfung UND Einstellung DER SeitenbesenhöhePrüfung UND Einstellung DER Hauptkehrwalzenhöhe AUSBAU/EINBAU DER Hauptkehrwalze S311357 Batterieladung Prüfung DER Flapshöhe UND FunktionsfähigkeitVerschrottung FehlersucheIntroduction Table DES MatieresIntroduction Deballage / Livraison Securite Symboles UtilisesInstructions Generales Manuel Dutilisation Français Description DE LA Machine Structure ET Commandes DE LA MachineStructure ET Commandes DE LA Machine Description Caracteristiques Techniques Accessoires / OptionsCaractéristiques générales Valeurs Parties électriques ValeursCodes des couleurs Schema ElectriqueControle DES Batteries SUR UNE Machine Neuve UtilisationAvant LA Mise EN Marche Mise EN Marche ET Arret DE LA MachineVidange DU Conteneur Dechets Machine AU TravailApres Lutilisation DE LA Machine Inactivite Prolongee DE LA MachinePlan Recapitulatif Dentretien Programme EntretienControle DU Cable DU Chargeur DE Batterie Procédure Toutes lesDepose / Repose DU Balai Lateral Controle ET Reglage DE LA Hauteur DU Balai LateralControle ET Reglage DE LA Hauteur DU Balai Central Depose / Repose DU Balai Central S311359 Controle DE LA Hauteur ET DU Fonctionnement DES Volets Chargement DES BatteriesMise EN Decharge Depistage DES PannesTable of Contents HOW to Keep this Manual Declaration of Conformity Manual Purpose and ContentsTarget Identification DataUNPACKING/DELIVERY Spare Parts and MaintenanceOther Reference Manuals Changes and ImprovementsSymbols SafetyGeneral Instructions English Machine Structure and Controls Machine DescriptionMachine Structure and Controls Description Technical Data ACCESSORIES/OPTIONSGeneral Values Electrical components ValuesColour code Wiring DiagramUSE Battery Check on a NEW MachineBefore Machine START-UP Starting and Stopping the MachineHopper Emptying Machine OperationAfter Machine USE Machine Long InactivityScheduled Maintenance Table MaintenanceBattery Charger Cable Check Procedure Every 10 hours Every 50 hoursSide Broom DISASSEMBLY/ASSEMBLY Side Broom Height Check and AdjustmentMain Broom Height Check Adjustment Main Broom DISASSEMBLY/ASSEMBLY S311357 S311358 S311359 Skirt Height and Operation Check Battery ChargingScrapping TroubleshootingInleiding InhoudsopgaveInleiding Verpakking VERWIJDEREN/AFLEVERING Veiligheid Gebruikte SymbolenAlgemene Instructies Gebruiksaanwijzing Nederlands Opbouw EN Bedieningselementen VAN DE Machine Beschrijving VAN DE MachineOpbouw EN Bedieningselementen VAN DE Machine Beschrijving Technische Eigenschappen Accessoires / OptiesAlgemeen Waarden Elektrische onderdelen WaardenKleurcodering Elektrisch SchemaControle VAN DE Accus OP EEN Nieuwe Machine GebruikVoor HET Starten VAN DE Machine DE Machine Starten EN StoppenDE Afvalcontainer Legen Machine in BedrijfNA Gebruik VAN DE Machine Lange Periode VAN StilstandProcedure Elke 10 uur Elke 50 uur Elke 200 uur Elke 400 uur OnderhoudsschemaOnderhoud Controle VAN DE Kabel VAN DE AcculaderDEMONTAGE/MONTAGE VAN DE Zijborstel DE Hoogte VAN DE Zijborstel Controleren EN AfstellenDE Hoogte VAN DE Hoofdborstel Controleren EN Afstellen DEMONTAGE/MONTAGE VAN DE Hoofdborstel Opmerking Accu Opladen Controle VAN DE Hoogte EN Werking VAN DE FlapsVerwijdering Storingen Lokaliseren

SW 750 specifications

The Nilfisk-ALTO SW 750 is a compact and highly efficient walk-behind scrubber dryer designed for a variety of indoor cleaning applications. Catering to the needs of small to medium-sized facilities, this machine excels in providing deep and effective cleaning while maximizing productivity. With its user-friendly design and advanced technologies, it is an ideal solution for maintenance in schools, shops, warehouses, and healthcare facilities.

One of the standout features of the Nilfisk-ALTO SW 750 is its robust construction and high maneuverability, which allows operators to navigate tight corners and congested areas with ease. The machine is equipped with a 12-volt battery that offers an impressive run time, ensuring that users can complete large cleaning tasks without interruption. The presence of an onboard charger adds to its convenience, allowing for quick and simple recharging between shifts.

The SW 750 utilizes an efficient scrub deck that combines a high-performance brush system with a powerful vacuum system. This dual-action feature ensures that dirt and debris are effectively removed from various surfaces, leaving floors spotless and dry. The machine’s adjustable brush pressure allows operators to customize the cleaning process based on the specific needs of different floor types, whether it be tile, concrete, or carpet.

Innovative technologies are integrated into the Nilfisk-ALTO SW 750 to enhance its cleaning capabilities. The machine includes the Ecoflex system, which provides users the option to adjust the amount of water and detergent used during cleaning. This not only helps in achieving excellent cleaning results but also promotes environmental sustainability by reducing chemical usage. Additionally, the machine features a Smart Key system, allowing for easy access control to prevent unauthorized use.

Another noteworthy characteristic of the SW 750 is its low noise operation, making it suitable for use in noise-sensitive environments. With a noise level significantly lower than many traditional scrubbers, it allows for cleaning operations to continue even during business hours without disturbing customers or staff.

Overall, the Nilfisk-ALTO SW 750 is a versatile and reliable cleaning solution tailored for efficient floor maintenance. Its combination of powerful cleaning performance, ease of use, and innovative technologies makes it an essential tool for professionals looking to maintain cleanliness in various settings. With its focus on user comfort and environmental responsibility, the SW 750 stands out as a leader in walk-behind scrubber technology.
Top Page Image Contents