Nilfisk-ALTO SW 750 manuel dutilisation Skirt Height and Operation Check, Battery Charging

Page 55

USER MANUAL

ENGLISH

SKIRT HEIGHT AND OPERATION CHECK

1.Drive the machine on a level ground that is suitable for checking the skirt height.

2.Turn the main switch (1) to “0”.

3.Check that the height from the ground of the side skirts (A and B, Fig. 11) is within 0 and 2 mm.

Check the skirts for integrity, cuts or tears, which can reduce the machine vacuum capabilities. If necessary replace the side skirts (see the procedure in the Service Manual).

4.Check that the front and rear skirts (C and D, Fig. 11) slightly rub on the ground. Check the skirts for integrity, cuts or tears, which can reduce the machine vacuum capabilities. Note that the front skirt has typical vertical cuts (E). If necessary replace the front and rear skirts (see the procedure in the Service Manual).

BATTERY CHARGING

1.Drive the machine to the appointed recharging area and ensure that it cannot move independently.

2.Turn the main switch (A, Fig. 12) to "0".

3.Remove the battery charger cable (B) from the housing

(C) and connect it to the electrical mains.

CAUTION!

Before connecting the battery charger (B), ensure that frequency and voltage values, indicated on the machine serial number plate (33), match the electrical mains voltage.

In case of doubt, do not connect the plug to the electrical mains, but contact the qualified personnel.

4.While charging the batteries, the red warning light (D) and the yellow warning light (E) turn on in sequence. When the green warning light (F) turns on, the batteries are charged.

5.Disconnect the battery charger cable (B) from the electrical mains and place it in the housing (C).

NOTE

When the battery charger is connected to the electrical mains, all machine functions are automatically disabled.

B

D

E

AC

A-B

D C

0-2 mm 0-0.08 in

S311360

Figure 11

A

F

E

D

B

C

S311361

Figure 12

SW 750

146 3080 000(1)2006-10 A

17

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Deutsch Français English Nederlands Sweeper Einleitung InhaltsverzeichnisEinleitung AUSPACKEN/AUSLIEFERUNG Sicherheit Benutzte SymboleAllgemeine Hinweise Betriebsanleitung Deutsch Struktur UND Bedienelemente DER Maschine MaschinenbeschreibungStruktur UND Bedienelemente DER Maschine Beschreibung Elektrische Teile Werte ZUBEHÖRE/OPTIONENTechnische Daten Allgemein WerteFarbencodes SchaltplanMaschinenanlassen UND -ABSTELLEN BetriebPrüfung DER Batterien AN Einer Neuen Maschine VOR DEM Anlassen DER MaschineLange Ausserdienststellung DER Maschine Maschine in BetriebEntleerung DES Abfallbehälters Nach DER MaschinenbenutzungVorgang Alle WartungÜbersichtstabelle DER Planmässigen Wartung Prüfung DES LadegerätkabelsAUSBAU/EINBAU DES Seitenbesens Prüfung UND Einstellung DER SeitenbesenhöhePrüfung UND Einstellung DER Hauptkehrwalzenhöhe AUSBAU/EINBAU DER Hauptkehrwalze S311357 Batterieladung Prüfung DER Flapshöhe UND FunktionsfähigkeitVerschrottung FehlersucheIntroduction Table DES MatieresIntroduction Deballage / Livraison Securite Symboles UtilisesInstructions Generales Manuel Dutilisation Français Description DE LA Machine Structure ET Commandes DE LA MachineStructure ET Commandes DE LA Machine Description Parties électriques Valeurs Accessoires / OptionsCaracteristiques Techniques Caractéristiques générales ValeursCodes des couleurs Schema ElectriqueMise EN Marche ET Arret DE LA Machine UtilisationControle DES Batteries SUR UNE Machine Neuve Avant LA Mise EN MarcheInactivite Prolongee DE LA Machine Machine AU TravailVidange DU Conteneur Dechets Apres Lutilisation DE LA MachineProcédure Toutes les EntretienPlan Recapitulatif Dentretien Programme Controle DU Cable DU Chargeur DE BatterieDepose / Repose DU Balai Lateral Controle ET Reglage DE LA Hauteur DU Balai LateralControle ET Reglage DE LA Hauteur DU Balai Central Depose / Repose DU Balai Central S311359 Controle DE LA Hauteur ET DU Fonctionnement DES Volets Chargement DES BatteriesMise EN Decharge Depistage DES PannesTable of Contents Identification Data Manual Purpose and ContentsHOW to Keep this Manual Declaration of Conformity TargetChanges and Improvements Spare Parts and MaintenanceUNPACKING/DELIVERY Other Reference ManualsSymbols SafetyGeneral Instructions English Machine Structure and Controls Machine DescriptionMachine Structure and Controls Description Electrical components Values ACCESSORIES/OPTIONSTechnical Data General ValuesColour code Wiring DiagramStarting and Stopping the Machine Battery Check on a NEW MachineUSE Before Machine START-UPMachine Long Inactivity Machine OperationHopper Emptying After Machine USEProcedure Every 10 hours Every 50 hours MaintenanceScheduled Maintenance Table Battery Charger Cable CheckSide Broom DISASSEMBLY/ASSEMBLY Side Broom Height Check and AdjustmentMain Broom Height Check Adjustment Main Broom DISASSEMBLY/ASSEMBLY S311357 S311358 S311359 Skirt Height and Operation Check Battery ChargingScrapping TroubleshootingInleiding InhoudsopgaveInleiding Verpakking VERWIJDEREN/AFLEVERING Veiligheid Gebruikte SymbolenAlgemene Instructies Gebruiksaanwijzing Nederlands Opbouw EN Bedieningselementen VAN DE Machine Beschrijving VAN DE MachineOpbouw EN Bedieningselementen VAN DE Machine Beschrijving Elektrische onderdelen Waarden Accessoires / OptiesTechnische Eigenschappen Algemeen WaardenKleurcodering Elektrisch SchemaDE Machine Starten EN Stoppen GebruikControle VAN DE Accus OP EEN Nieuwe Machine Voor HET Starten VAN DE MachineLange Periode VAN Stilstand Machine in BedrijfDE Afvalcontainer Legen NA Gebruik VAN DE MachineControle VAN DE Kabel VAN DE Acculader OnderhoudsschemaProcedure Elke 10 uur Elke 50 uur Elke 200 uur Elke 400 uur OnderhoudDEMONTAGE/MONTAGE VAN DE Zijborstel DE Hoogte VAN DE Zijborstel Controleren EN AfstellenDE Hoogte VAN DE Hoofdborstel Controleren EN Afstellen DEMONTAGE/MONTAGE VAN DE Hoofdborstel Opmerking Accu Opladen Controle VAN DE Hoogte EN Werking VAN DE FlapsVerwijdering Storingen Lokaliseren

SW 750 specifications

The Nilfisk-ALTO SW 750 is a compact and highly efficient walk-behind scrubber dryer designed for a variety of indoor cleaning applications. Catering to the needs of small to medium-sized facilities, this machine excels in providing deep and effective cleaning while maximizing productivity. With its user-friendly design and advanced technologies, it is an ideal solution for maintenance in schools, shops, warehouses, and healthcare facilities.

One of the standout features of the Nilfisk-ALTO SW 750 is its robust construction and high maneuverability, which allows operators to navigate tight corners and congested areas with ease. The machine is equipped with a 12-volt battery that offers an impressive run time, ensuring that users can complete large cleaning tasks without interruption. The presence of an onboard charger adds to its convenience, allowing for quick and simple recharging between shifts.

The SW 750 utilizes an efficient scrub deck that combines a high-performance brush system with a powerful vacuum system. This dual-action feature ensures that dirt and debris are effectively removed from various surfaces, leaving floors spotless and dry. The machine’s adjustable brush pressure allows operators to customize the cleaning process based on the specific needs of different floor types, whether it be tile, concrete, or carpet.

Innovative technologies are integrated into the Nilfisk-ALTO SW 750 to enhance its cleaning capabilities. The machine includes the Ecoflex system, which provides users the option to adjust the amount of water and detergent used during cleaning. This not only helps in achieving excellent cleaning results but also promotes environmental sustainability by reducing chemical usage. Additionally, the machine features a Smart Key system, allowing for easy access control to prevent unauthorized use.

Another noteworthy characteristic of the SW 750 is its low noise operation, making it suitable for use in noise-sensitive environments. With a noise level significantly lower than many traditional scrubbers, it allows for cleaning operations to continue even during business hours without disturbing customers or staff.

Overall, the Nilfisk-ALTO SW 750 is a versatile and reliable cleaning solution tailored for efficient floor maintenance. Its combination of powerful cleaning performance, ease of use, and innovative technologies makes it an essential tool for professionals looking to maintain cleanliness in various settings. With its focus on user comfort and environmental responsibility, the SW 750 stands out as a leader in walk-behind scrubber technology.
Top Page Image Contents