Heath Zenith 598-1125-02 manual 6a Mount with Double Sided Tape, Install Chime

Page 3

chime case or inside the existing chime case on a resonating chamber (DO NOT mount on chime bars). To assist with wire routing, the microphone wires can be temporarily removed from the wire terminals (see Figure 6) by loosening the terminals with Phillips screwdriver. Route wires through the slot on the transmitter (see Figure 6). Double-sided tape is provided to attach the microphone to your existing chime case.

4.Adjust the Microphone Sensitivity so that it is at the least sensitive position to reliably activate the transmitter. If the sensitivity is set too high, it may false trigger on common household noises.

5.When the system is working properly, carefully mark the desired location of the Extension Transmitter, and go to step 6 for final installation.

6a - Mount with Double Sided Tape

❐Install the battery cover.

❐Peel the protective backing from one side of two pieces of the double sided tape. Apply the tape to the two recessed areas on the back of the transmitter.

❐Remove the remaining protective backing. Carefully stick the transmitter to the

exact location marked in step 5.

6b - Mount with Screws and Hollow-Wall Fasteners

❐Temporarily remove the batteries.

❐Hold the transmitter in the desired location, and mark the two mounting holes.

❐Set the transmitter aside. Drill two 7/32" mounting holes. Tap the hollow-wall fasteners into the two holes.

❐Hold the transmitter in place, and secure with the two screws provided.

❐Reinstall the batteries and the battery cover.

Wire Terminals

Wire Routing

Slot

Mounting Holes

Figure 6

3.Install Chime.

1.The decorative chime unit can stand as a tabletop unit or be wall mounted using keyholes on rear of chime and mounting hardware provided.

2.To mount with screws and hollow-wall fasteners, drill two pilot holes located 2" apart (see Figure 4) at desired height. Use provided mounting screws and wall anchors as needed. Leave approximately 1/8" gap between wall and mounting screw head.

598-1125-02

- -

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Install batteries in transmitter and chime Weatherproof Long Range Wireless Chime With Chime ExtenderKeyholes Jumpers Battery OrientationVolume Control Install Extension TransmitterInstall Chime 6a Mount with Double Sided Tape6b Mount with Screws and Hollow-Wall Fasteners Code Settings Code and Tune SettingsTune Settings Tune SettingInside Chime does not sound TroubleshootingTechnical Service No Service Parts Available for this ProductRegulatory Information TWO Year Limited WarrantyPuentes Botón de prueba Instale las baterías en el transmisor y la campanaRanura guía del alambre Micrófono Control Del VolumenAgujeros Puentes Orientación de la batería6b Montaje con tornillos y sujetadores para pared hueca 6a Montaje con cinta adhesiva a los dos ladosInstalación de la campana Programaciones del código y del tonoProgramación del tono Cambio de pila del transmisorProgramación Del tono La campana suena cuando hay ruidos altos Análisis de AveríasServicio Técnico La campana no suenaGarantía Limitada a 2 Años Información RegulatoriaInstallez les piles dans l’émetteur et dans le carillon Cavaliers Sens des Piles CommandeInstallation de l’émetteur de prolongateur Orifices allongésInstallez le carillon 6a Montage avec ruban à deux faces adhésives6b Montage avec vis et ancrages pour murs creux Réglages du code Réglages du code et de la mélodieRéglage de la mélodie Réglage de La mélodieIntérieur de Réglage de la Mélodie Lémetteur Dépannage Le carillon ne sonne pasDéclenchement intempestif du carillon par les forts bruits Service Technique Renseignements de règlementsAucune pièce de rechange n’est disponible pour ce produit Garantie Limitée DE 2 ANS 598-1125-02 598-1125-02
Top Page Image Contents