Hearth and Home Technologies SANTAFE-B1 owner manual Straight Out, Degree

Page 13

Santa Fe Pellet Stove

R

B. Through The Wall

Horizontal termination cap must be a minimum of 12 inches. (305mm) from the wall. Approved for mobile home instal- lations. Must use 3 or 4 inch (76-102mm) “L” or “PL” listed pellet venting or listed double wall pipe and a Quadra-Fire Outside Air Kit in mobile homes.

NOTE:

In Canada, where passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365

Straight Out

6 in.

(152mm) Minimum From Glass

2in.

(51mm)

Minimum

Horizontal

Wall Termination

Thimble Cap

12 in.

(305mm) Minimum

Non-combustible Hearth Pad

Figure 13.1

45 Degree

Illustration shows venting going in both directions. Choose which one is best for your installation.

12 in. (305mm)

Minimum

Wall

Thimble

12in.

(305mm) Minimum

2 in. (51mm) Minimum

2in.

(51mm) Minimum

Figure 13.2

September 1, 2008

7001-142D

Page 13

Image 13

Contents Santa FE Pellet Stove Serial Number Model Name Santa Fe Pellet StoveLocation Back side of left side panel Table of Contents Listing and Code Approvals Getting Started Design, Installation & Location Fire Safety ConsiderationsAppliance Location Thermostat LocationInspect Appliance & Components and Pre-Use Check List Santa Fe Pellet Stove Tools And Supplies NeededAppliance Dimensions 3Dimensions and ClearancesSanta Fe Pellet Stove Clearances to Combustibles UL and ULC Santa Fe Pellet Stove Hearth Pad Requirements UL and ULC Exception for Horizontal InstallationsHearth Pad Requirements Venting Termination Requirements Chimney and Exhaust ConnectionSanta Fe Pellet Stove Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculaton Alcove Venting SystemsDegree Straight OutSanta Fe Pellet Stove Through The Wall Through The Wall & Vertical Santa Fe Pellet Stove VerticalAlternate Masonry MasonryMobile Home Outside Air Kit Instructions 7Appliance Set-UpRear Vent and Rear Vent to Top Vent Adapter Installation Santa Fe Pellet Stove Top Vent Adapter InstallationInstalling the Top Vent Adapter Notch Thermocouple Cover Installing the Trim Ring Installing the GrilleIncluded in Kit 1 Grille Santa Fe Pellet Stove Thermostat Installation Fuel Size And Material General Operating Information Operating InstructionsFeed Rate Adjustment Instructions Fire CharacteristicsFeed Adjustment Control Rod Wing Nut Set Screw Santa Fe Pellet Stove Before Your First FireSanta Fe Pellet Stove Iginition Cycles Frequently Asked QuestionsSymption TroubleshootingPossible Cause Corrective Action Page Page Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartFrequency Daily Weekly Monthly Yearly Types of FuelCleaning Ash Pan Cleaning Firepot with Cleaning Rod & Firepot ScraperAsh Removal from Firebox Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cont’d Cleaning the Exhaust PathCleaning Exhaust Blower Requires No Lubrication Cleaning the GlassCleaning Convection Blower Requires No Lubrication Door Latch InspectionImmediate Attention and Cleaning is Required Santa Fe Pellet Stove High Ash Fuel Content MaintenanceExhaust Blower Replacement Convection Blower ReplacementWing Nut Snap Disc #2 ReplacementIgniter Replacement Baffle & Brick Replacement Glass Replacement Reference Materials Wiring Harness See .1 below Vacuum SwitchSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FSanta Fe Pellet Stove Component Locations Description Part Number Santa Fe Pellet Stove Exploded ViewsDescription Nbr Item # Service Parts Description Part Nbr Santa Fe Pellet Stove Service Parts and AccessoriesLVGRL-SF-NL Accessory Description Part NumberDate of Service Performed By Description of Service Santa Fe Pellet Stove Service And Maintenance LogCONDITIONS, Exclusions & Limitation of Liability Santa Fe Pellet Stove Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d Telephone Contact Information