Aarrow Fires Gas Stove user manual Fitting and Arranging the Logs NG only, How to arrange the logs

Page 15

INSTALLATION INSTRUCTIONS

Fig. 10d

Fig. 10e

Plan View Of Coal Set Layout.

Note - Ensure that the pilot light is visible through the slot in the front right base matrix and that the pilot flame is not impinged.

FITTING AND ARRANGING THE LOGS (NG ONLY)

Ensure the appliance is cold

Safety Notice - Please see SAFETY NOTICES ref. Coal / Log set, page 3.

Warning: The logs and matrix are fragile, ensure they are handled carefully.

Ensure location is correct. Do not force the matrix into position. If any of the logs and/or rear matrix is damaged, they must be replaced with genuine Aarrow parts.

Warning: An incorrect log layout may cause soot to build up inside the stove and therefore invali- date the guarantee.

AB

C

 

 

 

 

G

 

 

 

 

 

 

D

F

 

E

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 11

Key For Contents To NG Log Set - A = Rear log matrix (black in colour) B = Loose Embers (bagged)

C = Curved Log

D = Y Shape Log

E = Central Log (Knotted Lump Protruding) F = 3x Small Twigs

G = 1x Large Twig

How to arrange the logs

1)Position the rear log matrix in the centre at the rear of the burner. The base of the matrix should slot down behind the burner. See Fig. 12a.

2)Lay the Y shape log to the right hand side of the burner. Ensure that the Y open section is upper most and is resting onto the cutout flat area to the right of the rear log matrix. The base should be approimately 30mm from the front of the stove window opening. See Fig 12a.

3)Take the curved log and place this to the left hand side of the burner. Make sure that the base of this log is again approx. 30mm from the front of the stove and the upper end of the log is resting on the grooved notch within the rear log matrix. See Fig 12a. Note, there should be a gap between both side logs when resting correctly on the rear matrix.

4)Next scatter the loose embers onto the burner area. Take care not to obstruct the pilot assembly.

Fig. 12a

5)Lay the central log, from the centre front of the burner to the rear of the stove. Sitting the upper portion of the central log onto the edge of the

Aarrow Sherborne GSL CF

15

Image 15
Contents Sherborne GSL Contents GuaranteeSpare Parts Installation Instructions Safety NoticesGeneral Information Fit for purpose Stove locationPacked details Unpacking noteMain Box Installation Instructions Important Notices Statutory RequirementsCertification Min. Heat Setting Installation Instructions Technical DataInstalling the Stove Max. Heat SettingInstallation Instructions Preparation of the Stove Stove must not be installed against a combustible wallStove Location Non-Combustible shelf clearances Installation Instructions Shelf ClearancesInstallation Instructions Flue System Closure Plates Rear Flue OptionsTOP Flue Options =See Graph Pressure Test Sequence Installation Instructions Connecting the GAS SupplyFitting and Arranging the Coals Both NG & LPG versions Fitting and Arranging the Logs NG only How to arrange the logsFitting and Arranging the Logs LPG only Installation Instructions For a Manual Stove Without Remote Control Proceed to Installation of Remote Control SystemAssemble Motor Slot Assemble ReceiverHandset Commissioning the Stove Fire TestingAdvise the end user Checklist Servicing Replacement of the Glass Servicing Burner and Valve Assembly RemovalServicing Annual Service Cleaning Outer SurfacesSee Safety Notices ref coal set OSD Pilot Fault DiagnosisDate of Visit Company Work Carried Out Signature Annual Service RecordAdditional Notes User Instructions User Instructions Lighting & Controlling the Fire User Instructions To turn the stove and the pilot offDo not try to force the control, wait the 60 seconds Temperature Display Remote Control Set the display from *C/24 h to *F/12 h and vice versa Thermostat and Timer Remote ControlProgramming the Desired Set Temperature Programming the TimerAutomatic Mode Auto in display for Temperature Control User Instructions User Instructions Important Notices User Instructions Shelf Clearances Part Description Visual Aid Part Number Spare PartsSpare Parts AFGS010 Aocshb Options & AccessoriesRemoteshb TraceshbPlease complete the following for you own records GuaranteeAdditional Notes ’ve checked it and it’s O.K