Aarrow Fires Gas Stove user manual Servicing Annual Service, Cleaning Outer Surfaces

Page 27

SERVICING

ANNUAL SERVICE

THIS GAS APPLIANCE MUST BE SERVICED EVERY TWELVE MONTHS BY A QUALIFIED GAS ENGINEER.

See "SAFETY NOTICES" ref coal set page 3.

Ensure the appliance is cold.

Step 1 Isolate the gas supply from the stove. Step 2 Remove the outer body of the stove. Step 3 Remove the glass.

Important: If the glass is broken or cracked or the glass gasket is damaged they must be replaced before the stove is used.

Step 4 Carefully remove and clean the loose coal

/logs set of any soot deposits using a soft brush.

Step 5 Clean the firebox of any soot deposits using a soft brush.

Step 6 Carefully lift out and clean the base coal matrix. Important: If any of the ceramic components are damaged they must be replaced with original Aarrow parts.

Step 7 Clean the burner top and surrounding areas with a vacuum cleaner.(See safety notices on page 3).

Step 8 Inspect the pilot assembly to ensure that it is clean, unobstructed and in good work ing order.

Step 9 Looking into the flue from inside the stove check that it is clear of any debris or obstructions.

Step 10 Check the system for gas soundness. Step 11 Check the ignition of the pilot and with

the pilot turned off check that the flame failure system is working.

Step 12 Relocate the base coal matrix (4x piece). Step 13 Relocate and position the loose coals or

re-assembly the log set.

Step 14 Light the pilot and check the operation of the stove and the flame picture.

Step 15 Relocate the glass frame assembly, ensuring all the screws are replaced and secure. (Use original screws only.)

Step 16 Refit the dummy fuel retainer.(2x screws) Step 17 Relocate the outer body of the stove. Step 18 If the stove is rear flued proceed to fit the

top flue cover plate into the canopy cutout ensuring the front tab is located under the canopy (see page 25, step 1a). Place the valve cover in front of the control valve.

Step 19 If the stove is top flued, proceed to fit the top flue infill piece (see page 25, step

1b). Place the valve cover in front of the control valve.

CLEANING OUTER SURFACES

It is best cleaned using a soft brush. Do not allow moisture to remain on the top while cold or surface rust may occur.

Aarrow Sherborne GSL CF

27

Image 27
Contents Sherborne GSL Contents GuaranteeSpare Parts Installation Instructions Safety NoticesGeneral Information Fit for purpose Stove locationPacked details Unpacking noteMain Box Installation Instructions Important Notices Statutory RequirementsCertification Min. Heat Setting Installation Instructions Technical DataInstalling the Stove Max. Heat SettingInstallation Instructions Preparation of the Stove Stove must not be installed against a combustible wallStove Location Non-Combustible shelf clearances Installation Instructions Shelf ClearancesInstallation Instructions Flue System Closure Plates Rear Flue OptionsTOP Flue Options =See Graph Pressure Test Sequence Installation Instructions Connecting the GAS SupplyFitting and Arranging the Coals Both NG & LPG versions Fitting and Arranging the Logs NG only How to arrange the logsFitting and Arranging the Logs LPG only Installation Instructions For a Manual Stove Without Remote Control Proceed to Installation of Remote Control SystemAssemble Motor Slot Assemble ReceiverHandset Commissioning the Stove Fire TestingAdvise the end user Checklist Servicing Replacement of the Glass Servicing Burner and Valve Assembly RemovalServicing Annual Service Cleaning Outer SurfacesSee Safety Notices ref coal set OSD Pilot Fault DiagnosisDate of Visit Company Work Carried Out Signature Annual Service RecordAdditional Notes User Instructions User Instructions Lighting & Controlling the Fire User Instructions To turn the stove and the pilot offDo not try to force the control, wait the 60 seconds Temperature Display Remote Control Set the display from *C/24 h to *F/12 h and vice versa Thermostat and Timer Remote ControlProgramming the Desired Set Temperature Programming the TimerAutomatic Mode Auto in display for Temperature Control User Instructions User Instructions Important Notices User Instructions Shelf Clearances Part Description Visual Aid Part Number Spare PartsSpare Parts AFGS010 Aocshb Options & AccessoriesRemoteshb TraceshbPlease complete the following for you own records GuaranteeAdditional Notes ’ve checked it and it’s O.K