Baldor iMN1800 manual Lmpy Series Polynoid Linear Motor Holding Option, Switching, Single Holding

Page 18

LMPY Series Polynoid Linear Motor Holding Option

Mounting:

The rectifier package is wired externally in the stator circuit.

 

For 115/60Hz, rectifier package CO0126A00 is provided.

 

For 230/60Hz, rectifier package CO0125A00 is provided.

 

Rated holding force is only achieved when the keeper plate is against the holding coil. To

 

reduce shock loads, a shock absorbing connection between the polynoid rod and the load

 

is recommended.

Switching:

Two switching modes can be used for various applications.

 

Single Holding:

S Energized constantly except momentary interruption to release holding so rod can be reversed.

S Energized only during period when holding is required.

S Energized only when rod is moving towards the holding end of the stator and during the holding period.

Double Holding:

S Energized constantly except momentary interruption to release holding so rod can be reversed.

S Energized only during period when holding is required.

S Double holding coils may be switched together or one at a time.

Note: Double holding coil units are normally supplied with 2 yellow leads and one small diameter black lead so that the holding coils may be operated independently by applying rated voltage to the yellow and black lead. The wire marker on one yellow lead indicates the lead that operates the holding coil on the lead egress end of the stator. If desired, the 2 yellow leads can be tied together for simultaneous operation of both holding coils.

WIRING GUIDES:

1. Single Holding:

MN1800

Installation & Operation 2-11

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Linear Motors MN1800Table of Contents Ii Table of Contents MN1800 Limited Warranty OverviewIndicates a condition that can cause damage to equipment Do not apply AC power before you ensure that all grounding Lifting, installing, operating and maintaining operationsInstallation, operation and maintenance of this equipment Attempt to install operate or maintain this equipmentUnpacking ReceivingStorage HandlingGeneral Information MN1800 Clean Room LocationMounting a Stage to the Machine Base and Payload To Stage Lmac Connection Diagram Lmac Linear Induction MotorLmbr Series Brush DC Linear Servo Motor Brushless Linear Iron Core Servo Motor Installation Alternate Installation Refer to FigureLmbl Series AY1763A00 Leadwire Connection Wire ColorMotor Cable Hall Cable Limit Cable Modular Magnet Track Installation Brushless Linear Iron Core Servo Motor Modular Magnet Track Hall Cable Limit CableLmcf Series Brushless Linear Cog Free Servo Motor Air Gap SpacingLmnc Moving Coil Type Pin# ColorLmnm Moving Magnet Type Non Commutated DC Linear Servo Motor Single Holding SwitchingLmpy Series Polynoid Linear Motor Holding Option Double HoldingLmpy Series Leadwire ConnectionMotor Cable Signal Name Wire Color Polynoid Linear Motor Holding OptionAY0165A00 Leadwire Connection 9 pin to flying leads Adjust Air GapMaintenance Lmss Series Linear StepperLmss Series Air Bearing Motor Cleaning the Forcer and PlatenInstallation Mounting the Forcer on the Platen Removing the Forcer from the PlatenLmds Series Dual Axis Linear Stepper Motor Items Required but not IncludedStage Specifications Disclaimer Positioning StagesUnpacking Construction Stage specificationsLSE Series Enclosed Position Stage General Description Bearing typeAY1779A00 LSE with Renishaw Encoder RGH24 Flying Leads LD9125A01 Limit only Color Pin# Description LD9137A01 Limit only Color Pin# DescriptionLD9124A00 Limit and Home, Axis 1, Internal Pin# Color LSE Stage Connector Locations LSC Series Cross Roller Position Stage General Description AY1775A00 Leadwire Connection for LinDrive 15 pin LD9125A02 H-Limit and Home Color Pin# Description LSS Series Single Bearing Position Stage AY1759A00 Renishaw RSF EncoderAY1801A00 Stages with Renishaw Encoder RGH22 Flying Leads AY1802A00 Stages with Renishaw Encoder RSF Flying LeadsLeadwire Connection LD9103A00 LXS Connections Female LinDrive Connections MaleLD9114A00 Motor / Limit Connections Pin Circular Connector Male Pin D Sub MalePin D Sub Female LD9119A02 Color Pin# Description LSX Leadwire Connection Limit Switch PigtailsLD9119A01 Color Pin# Description LD9137A02 Limit and HomePin Encoder Connector Pin Encoder ConnectionsBearing Maintenance Recirculating Bearing Rail And Block Cross Roller Type BearingRSF Series MSA6x Enclosed Type Encoder MaintenanceTechnical Data Color Description FunctionRSF Series MS6x Open Type Glass Scale Renishaw RGH22 series Open Type Metal Scale Renishaw RGH22 series Open Type Metal Scale Specifications Associated ComponentsEncoder Head Output Connector Pin Assignment Elgo Mix 4 series Magnetic TypeMix 4 and Mix 5 Dial Settings Resolution using 4x multiplier Elgo Mix 5 series Magnetic TypeEncoder Specifications RequirementsCables and Cable Chain Procedures Additional Cables Baldor Electric Company  Baldor Electric Company MN1800 01 C&J1500

iMN1800 specifications

The Baldor iMN1800 is a comprehensive industrial motor drive, engineered for a wide range of applications in various sectors such as manufacturing, robotics, and automation. This drive exemplifies Baldor's commitment to innovation, performance, and efficiency, offering users advanced features that cater to modern industrial demands.

At the heart of the iMN1800 is its state-of-the-art motor control technology, designed to provide precise control over motor speed and torque. This is achieved through a sophisticated algorithm that adjusts the motor's performance in real-time, ensuring reliability and efficiency. The iMN1800 is compatible with various forms of electric motors, including AC induction and permanent magnet synchronous motors, making it versatile for numerous applications.

One of the standout features of the Baldor iMN1800 is its energy efficiency. It complies with various energy standards, which not only helps reduce operational costs but also minimizes the environmental impact associated with industrial operations. With an impressive efficiency rating, the iMN1800 contributes to lower energy consumption, making it an economically viable solution for businesses aiming to enhance sustainability.

In terms of connectivity, the iMN1800 incorporates advanced communication protocols such as Ethernet/IP and Modbus, allowing for seamless integration into existing industrial networks. This feature facilitates real-time monitoring and control, empowering operators to make informed decisions based on live data. The user-friendly interface enables quick access to essential parameters for both configuration and diagnostics, ensuring ease of use for technicians and engineers alike.

Moreover, the iMN1800 is built with robust construction materials, ensuring durability in demanding environments. Its rugged design allows it to withstand harsh conditions, including high temperatures and vibrations, common in industrial settings. This reliability contributes to reduced downtime and maintenance costs, promoting a more productive work environment.

The Baldor iMN1800 also features advanced safety mechanisms, including overload protection and short-circuit protection, guaranteeing the safety of both personnel and equipment. These attributes align with modern safety standards, making it a trusted choice for industries that prioritize workplace safety.

In summary, the Baldor iMN1800 is a top-tier industrial motor drive that combines advanced motor control technology, energy efficiency, robust construction, and enhanced safety features. Its flexibility and connectivity make it a valuable asset for diverse industrial applications, ultimately driving operational efficiency and effectiveness.
Top Page Image Contents