Brother PQ1300 Changing Needles and Light Bulb, Changing the Feed Pin, Remove screwdriver

Page 10

Changing Needles and Light Bulb

Note

Please make sure power is off before carrying out the following operations. There is a chance of injury if the machine accidentally starts running during this operation.

Changing the Feed Pin

1Set the feed dogs to "velvet"

position. (see Page 5)

2Remove needle, presser

foot and needle plate.

Note

Please make sure power is off before carrying out the following operation. The glass plate over the light bulb will be hot immediately after using the machine, so you should wait until the machine has had a chance to cool down before changing bulbs.

CONTENTS

Accessories

Changing the Needle

1Turn the sewing machine off. Raise needle to highest position using hand wheel, and lower presser foot.

2Loosen screw with screw- driver, and remove needle.

3Insert new needle, and tighten screw. Make sure needle is screwed in tightly.

✽Check needles on a flat surface to make sure they're not bent.

Screwdriver

The needle should lay parallel to a surface.

flat surface

Lay needle on a flat surface

(such as the needle plate or a plate

of glass).

3Lower presser foot and turn hand wheel until feed

pin is in its highest position.

4Insert small screwdriver (included) as shown in diagram.

5While holding spring with fingertip, lower the feed pin changer onto the needle to pick it up.

6Attach new feed pin to feed pin changer, lower and attach while holding spring with fingertip.

7Remove screwdriver.

8Re-attach needle plate, needle and presser foot.

Changing Light Bulbs

1Turn off power.

2 Remove screws from Screwdriver head.

3Remove head.

4Unscrew bulb and remove.

5 Screw in new bulb. Rated 120V 15W

6 Re-attach head and tighten screw.

Light

Parts	Names
	of
Begin	Before You


Light Bulb	Needles and		Changing
	Threading
Needle Chart	Samples and		Stitch
Presser Feet		Changing
Sewing		Basic
Machine	Your		Caring for

Note

HLX5 needles should be uses; however, Schmetz 130/705H may also be used under normal

610 circumstances.

Bulb

Shooting

Trouble

Image 10

Contents PQ1300 Important Safety Instructions For repair or adjustment For a longer service lifeFor safe operation Contents Accessories Part Name Part CodeNames of Parts Before You Begin Presser Foot Lift Lever Setting up the knee controlPressure Adjustment Dial Knee LiftIndicator Lamp Needle Stop Position Button Light SwitchFoot Pressure and Feed Dog Position Remove screwdriver Changing Needles and Light BulbChanging the Feed Pin Re-attach needle plate, needle and presser footPut spool of thread on spool pin ThreadingSpool Cushion Spool Cap Spool of Thread Wound thread812 Bobbin InsertionPin Using the Automatic Needle ThreaderThreader Make sure thread take-up leverHow to Pull Out the Bobbin Thread Turn once to pull out the bobbin ThreadLower presser foot Stitch Samples and Needle ChartStitch Samples Thread Tension Raise needle to highest pointChanging Sewing Feet Zipper Foot Changing Presser Feet126 Presser FeetPin Feeding for hard-to-handle fabrics Basic SewingBasic Sewing Pin Feeding Unit148 Rolled Hem FootSew zipper onto fabric along Zipper FootMark Invisible Zipper Foot 1620Lining Precautions Keep Your Sewing Machine CleanCaring for Your Machine Pleasetake Trouble Shooting1822 YournearestMemo Pour une vie prolongée de votre machine 204Précautions d’utilisation Pour la réparation et le réglagePoints dessai et tableau daiguilles Accessoires Enfilage Nom des piècesAvant de commencer Changement du pied-de- bicheNo. de pièce Désignation Code de pièce Accessoires226 RemarquePages 24 et Nom des piècesTable dextension Au genouSélecteur de tension Avant de commencer248 VolantLevier du pied-de-biche Sélecteur de réglage de pressionPression du pied-de-biche et position 2630Bouton de ciseaux Des griffes dentraînementTournevis Ampoule de lampe Retirer le tournevisRemonter la tête et Remonter la plaque à aiguille et le pied-de- bicheCoussinet de bobine Capuchon de bobine Bobine de fil Enfilage2832 Appuyer sur la butée de canetteVolet de canette La pédaleEncoche à fil Si le fil est encore Utilisation de lenfileur automatiqueTorsadé, faire passer Comment sortir le fil de la canette 326 Points dessai et tableau daiguillesPoints dessai Tension des fils Permet de fixer des fermetures à glissière dissimulées Changement du pied-de-bicheChangement du pied-de-biche pied pour fermeture à glissière Peut également être utilisé avec un entraînement par ergotCouture de base Couture de basePied pour ourlet rouleauté Arrêt 3640Pied pour fermeture à glissière P o s i t i o n d u p i e d s o n t correctement alignéesFaufile DoublureDents Coudre 2 ou 3 points de renfort3842 Entretien de la machine à coudrePrécautions Si lon ne parvient pas à magasin où elle a étéachetée DépannageDes points sautent 29-31English French Part Function Pressure Adjustment Dial Off before servicing. Replace coverPièces Fonction Remplissage de la canettePour régler la longueur des points