Brother PQ1300 Using the Automatic Needle Threader, Pin, Make sure thread take-up lever, Hook

Page 13

Threading (2)

Note Please turn power is off before using automatic needle threader. Accidentally stepping on the foot controller during this operation could cause bodily injury or damage to the machine.

	Upper Threading		1
	Upper Threading
	7			1
				1
				6	7
					7
		6		4	2	9
	8	6	2	4	3	9
	8	4	2		3	0
			3			0
	5				8
				5	8	A
	9			● Make sure thread take-up lever	✽ If the thread is still
	0			● Make sure thread take-up lever	✽ If the thread is still
	0			is in highest position and presser	twisted, run the
		A		is in highest position and presser	twisted, run the
		A		foot is up.	thread through the
				foot is up.	thread through the
				✽ When using polyester, you	holes backwards as
	Using the Automatic Needle Threader			should run the thread through all	shown in diagram.
	Using the Automatic Needle Threader			three holes of the thread guide.
				three holes of the thread guide.

	Automatic
	Needle	Hook
	Threader	Hook
	Threader

Pin

CONTENTS
Accessories
Parts	Names
	of
Begin	Before You


Light Bulb	Needles and		Changing
	Threading
Needle Chart	Samples and		Stitch
Presser Feet		Changing
Sewing		Basic
Machine	Your		Caring for

1Pull hand wheel towards you until needle is in the highest position, and lower presser foot.

2Take thread in your left hand, and gently pull it forwards.

3Lower automatic needle threader.

✽Pull thread along the right side of the pin.

4Catch thread with hook.

✽Pull thread to the right, and make sure it has been caught with the hook.

5Raise needle threader lever while gently holding the end of the thread.

Shooting

Trouble

9

Image 13

Contents PQ1300 Important Safety Instructions For repair or adjustment For a longer service lifeFor safe operation Contents Part Name Part Code AccessoriesNames of Parts Before You Begin Pressure Adjustment Dial Setting up the knee controlPresser Foot Lift Lever Knee LiftIndicator Lamp Needle Stop Position Button Light SwitchFoot Pressure and Feed Dog Position Changing the Feed Pin Changing Needles and Light BulbRemove screwdriver Re-attach needle plate, needle and presser footSpool Cushion Spool Cap Spool of Thread ThreadingPut spool of thread on spool pin Wound threadBobbin Insertion 812Threader Using the Automatic Needle ThreaderPin Make sure thread take-up leverTurn once to pull out the bobbin Thread How to Pull Out the Bobbin ThreadStitch Samples Thread Tension Stitch Samples and Needle ChartLower presser foot Raise needle to highest point126 Changing Presser FeetChanging Sewing Feet Zipper Foot Presser FeetBasic Sewing Basic SewingPin Feeding for hard-to-handle fabrics Pin Feeding UnitRolled Hem Foot 148Sew zipper onto fabric along Zipper FootMark Invisible Zipper Foot 1620Lining Precautions Keep Your Sewing Machine CleanCaring for Your Machine 1822 Trouble ShootingPleasetake YournearestMemo Précautions d’utilisation 204Pour une vie prolongée de votre machine Pour la réparation et le réglageAvant de commencer Accessoires Enfilage Nom des piècesPoints dessai et tableau daiguilles Changement du pied-de- biche226 AccessoiresNo. de pièce Désignation Code de pièce RemarqueTable dextension Nom des piècesPages 24 et Au genou248 Avant de commencerSélecteur de tension VolantSélecteur de réglage de pression Levier du pied-de-bicheBouton de ciseaux 2630Pression du pied-de-biche et position Des griffes dentraînementRemonter la tête et Retirer le tournevisTournevis Ampoule de lampe Remonter la plaque à aiguille et le pied-de- biche2832 EnfilageCoussinet de bobine Capuchon de bobine Bobine de fil Appuyer sur la butée de canetteVolet de canette La pédaleEncoche à fil Si le fil est encore Utilisation de lenfileur automatiqueTorsadé, faire passer Comment sortir le fil de la canette 326 Points dessai et tableau daiguillesPoints dessai Tension des fils Changement du pied-de-biche pied pour fermeture à glissière Changement du pied-de-bichePermet de fixer des fermetures à glissière dissimulées Peut également être utilisé avec un entraînement par ergotCouture de base Couture de basePied pour ourlet rouleauté Pied pour fermeture à glissière 3640Arrêt P o s i t i o n d u p i e d s o n t correctement alignéesDents DoublureFaufile Coudre 2 ou 3 points de renfort3842 Entretien de la machine à coudrePrécautions Des points sautent DépannageSi lon ne parvient pas à magasin où elle a étéachetée 29-31English French Off before servicing. Replace cover Part Function Pressure Adjustment DialPièces Fonction Remplissage de la canettePour régler la longueur des points