KitchenAid W10520792B manual Install Custom Overlay Panel, Door Reversal-Side Swing Only

Page 11

WARNING

Excessive Weight Hazard

Option 1—Without Hinge-Side Space

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

2.Style 1—For gravity drain system, push the ice maker into position so that the ice maker drain tube is positioned over the PVC drain reducer. See “Gravity Drain System.”

Style 2—For drain pump system connect the drain pump outlet hose to the drain. See “Drain Pump System.”

3.Recheck the ice maker to be sure that it is level. See “Leveling.”

4.If it is required by your local sanitation code, seal the cabinet to the floor with an approved caulking compound after all water and electrical connections have been made.

29¹⁄₂"

(74.9 cm)

14¹⁷⁄₃₂"

(36.9 cm)

A

B

C

Install Custom Overlay Panel

IMPORTANT: Create custom overlay panel according to the specifications in the “Custom Panel Dimensions” section.

1.Install the ice maker.

2.Level the ice maker. See “Leveling.”

3.Place the ice maker under the cabinet so that the front edge of the custom panel will align with the front edge of the surrounding cabinets.

4.Hold the custom panel up to the ice maker and check that the opening and alignment are correct. Mark location of the panel as necessary.

5.Mark location of the handle. Remove the panel from the door and drill holes for the handle.

6.Install the door handle on the panel.

7.Remove the tape from the face of the door.

8.Remove the paper backing from the adhesive pads that are located on the door front.

9.Place the panel on the door, align with markings and apply pressure in the area of the adhesive pads.

10.Make sure the ice maker door opens and closes easily.

11.Pull the ice maker forward to access the top and sides of the door.

12.Remove the gaskets from the interior door panel and set aside.

13.Using the factory drilled holes as a guide, use a scribe and mark the drilling locations on the overlay panel.

14.Drill eight ¹⁄₈" x ¹⁄₂" (3.18 mm x 12.7 mm) deep holes into the overlay panel.

NOTE: Do not drill deeper than ¹⁄₂" (12.7 mm).

15.Use eight #8 x ¹⁄₂" pan-head wood screws to attach the panel to the door.

16.Replace the gaskets on the inner door panel.

17.Move the ice maker back into place under the counter.

A. #8 x ¹⁄₂" pan-head

B. Adhesive pads

wood screw

C. Custom panel

Option 2 - With Hinge-Side Spacer

A

B

29¹⁄₂"

(74.9 cm)

C

14⁵⁄₈"

 

(37.1 cm)

 

A. #8 x ¹⁄₂" pan-head

B. Adhesive pads

wood screw

C. Custom panel

Door Reversal—Side Swing Only

Tools Needed

Gather the required tools and parts before starting installation.

⁵⁄₁₆" wrench

Flat putty knife

¹⁄₄" wrench

Phillips screwdriver

Hinge pin

⁵⁄₁₆" hex-head hinge screw

Handle screw

End cap screw

11

Image 11
Contents Guide d’utilisation et d’entretien Use & Care GuideManual de uso y cuidado Table DES Matières Table of ContentsÍndice Tools and Parts ICE Maker SafetyInstallation Instructions Custom Panel Dimensions Location Requirements Unpack the Ice MakerConnect Water Supply Electrical RequirementsWater Supply Requirements Vacation or Extended Time Without UseKit Contains Drain Pump InstallationRear View Water Supply Line If Ice Maker Is Currently InstalledDrain Pump Installation Drain CapVent Tube Drain Pump Mounting Tab SlotSide View Connecting the DrainDrain Connection Gravity Drain SystemOption 2 With Hinge-Side Spacer Install Custom Overlay PanelDoor Reversal-Side Swing Only Option 1-Without Hinge-Side SpaceReplace Door Remove Stainless Steel Door Wrap Panel on some modelsDoor Stop and End-Cap Reversal Reverse HingesReverse Door Catch LevelingTop Hinge Bottom HingeWater Filter Status Light Install the Water FilterWater Filtration System How Your Ice Maker Works Using the ControlsICE Maker USE Normal Sounds CleaningICE Maker Care Interior Components Condenser Dirty or Clogged CondenserTo Shut Down the Ice Maker For Ice Makers with a Drain Pump InstalledVacation and Moving Care Ice Maker Seems Noisy TroubleshootingIce Maker Operation Ice Maker Will Not OperateIce Maker Runs But Produces No Ice Ice ProductionIce Quality For further assistance If you need replacement partsU.S.A CanadaAffresh* Stainless Steel Cleaner Performance Data SheetAccessories CleanerThis limited warranty does not cover Kitchenaid ICE Maker WarrantyPage Herramientas y piezas Seguridad DE LA Fábrica DE HieloInstrucciones DE Instalación Dimensiones del panel hecho a la medida Requisitos de ubicación Desempaque la fábrica de hieloConexión del suministro de agua Requisitos eléctricosRequisitos del suministro de agua Vacaciones o tiempo prolongado sin usoEl juego contiene Instalación de la bomba de desagüeConexión de la tubería de agua Vista posteriorInstalación de la bomba de desagüe Si la fábrica de hielo ya está instaladaTapa de desagüe Línea de suministro de aguaBomba de desagüe instalada Tubo de desagüeRanura de la lengüeta de montaje de la bomba de desagüe Ubicaciones de las piezasVista lateral Conexión del desagüeTubo de ventilación Sistema de desagüe por gravedadConexión del desagüe Instale el panel de revestimiento hecho La medidaSistema de la bomba de desagüe en algunos modelos Llave de tuercas de ¹⁄₄ Destornillador Phillips Bisagra inferior Inversión de las bisagrasCómo volver a colocar la puerta Bisagra superiorInstalación del filtro de agua NivelaciónSistema de filtración de agua Cómo invertir el seguro de la puertaReemplazo del filtro de agua Luz de estado del filtro de aguaProceso de elaboración de hielo USO DE LA Fábrica DE HieloCómo funciona su fábrica de hielo Uso de los controlesLimpieza Cuidado DE LA Fábrica DE HieloSonidos normales Condensador Un condensador sucio u obstruido Tornillo Espaciador de plástico Rejilla de corte Componentes interioresPara apagar la fábrica de hielo Cuidado durante las vacaciones y mudanzasLa fábrica de hielo no funciona Solución DE ProblemasFuncionamiento de la fábrica de hielo La fábrica de hielo funciona pero no produce hielo Producción de hieloCalidad del hielo Si necesita piezas de repuesto Problemas de plomeríaAyuda O Servicio Técnico En los EE.UULimpiador Hoja DE Datos DEL RendimientoAccesorios Filtro de aguaEsta garantía limitada no cubre Garantía DE LA Fábrica DE Hielo DE KitchenaidPage Outillage et pièces Instructions D’INSTALLATIONSécurité DE LA Machine À Glaçons Dimensions du panneau personnalisé Nettoyage avant l’utilisation Exigences d’emplacementDéballage de la machine à glaçons Enlèvement des matériaux d’emballageRaccordement à la canalisation d’eau Spécifications électriquesSpécifications de l’alimentation en eau Vacances ou longue période d’inutilisationVue arrière Raccordement du tuyau d’eau Installation de la pompe de vidangeBouchon de vidange Si la machine à glaçons est installéeInstallation de la pompe de vidange Contenu de l’ensembleEncoche de patte de montage de la pompe de vidange Pompe de vidange installéeTube de vidange Position des piècesVue latérale Raccordement au drain de vidangeTube de ventilation Vidange par gravitéRaccordement du drain de vidange Installation du panneau décoratif personnaliséSystème avec pompe de vidange sur certains modèles Inoxydable Option 2-Avec cale despacement côté charnièreInversion du sens de montage des charnières Réinstallation de la porteRéinstallation du revêtement de porte sur certains modèles Inversion du sens dinstallation de la gâche de porteSystème de filtration d’eau Installer le filtre à eauNivellement Témoin lumineux du filtre à eau Remplacement du filtre à eauUtilisation DE LA Machine À Glaçons Fonctionnement de la machine à glaçonsSons normaux Utilisation des commandesMode Max Ice glaçons max Alarme de porte entrouverteSystème de la machine à glaçons Entretien DE LA Machine À GlaçonsNettoyage Surfaces extérieuresComposants intérieurs Machine à glaçons avec pompe de vidange Précautions à prendre avant les vacances ou un déménagementArrêt de la machine à glaçons La machine à glaçons ne fonctionne pas DépannageProduction de glaçons Problèmes de plomberie Au Canada Assistance OU ServiceAccessoires Aux États-UnisSystème de filtration d’eau de la machine à glaçons Feuille DE Données SUR LA PerformanceLa présente garantie limitée ne couvre pas Garantie DE LA Machine À Glaçons KitchenaidW10520792B

W10520792B specifications

The KitchenAid W10520792B is an innovative component designed to elevate your culinary experience. This replacement part is particularly known for its reliability and efficiency, ensuring that your KitchenAid appliances function optimally. One of the main features of the W10520792B is its compatibility with various KitchenAid models, which makes it a versatile choice for users seeking to maintain their kitchen equipment in peak condition.

One notable characteristic of the W10520792B is its durable construction. Made from high-quality materials, it is designed to withstand the rigors of daily cooking tasks, providing longevity and consistent performance. This durability means that home chefs can rely on this part to perform under pressure, whether mixing, kneading, or whipping.

The W10520792B showcases KitchenAid's commitment to innovative design. The part utilizes advanced manufacturing techniques to ensure precision, which contributes to the overall efficiency of KitchenAid appliances. This attention to detail not only enhances the functionality of the equipment but also allows users to enjoy a more seamless cooking experience.

Another essential technology found within the W10520792B is its user-friendly installation process. Designed with the homeowner in mind, this component can typically be replaced without the need for professional assistance, saving both time and money. Clear instructional guidelines usually accompany the part, enabling even less experienced users to successfully complete the replacement with ease.

Moreover, the W10520792B is part of KitchenAid's commitment to sustainability. The materials used are often environmentally friendly, ensuring that customers can maintain their appliances while being conscious of their ecological footprint. This quality appeals to consumers who value both performance and environmental responsibility in their kitchen tools.

In summary, the KitchenAid W10520792B is an essential component that embodies quality, durability, and innovation. Its compatibility with various models, user-friendly installation, and sustainable materials make it an excellent choice for maintaining the high performance of KitchenAid appliances. Home cooks can rely on this part to enhance their cooking experience, allowing them to create delicious meals with confidence. Whether you are an aspiring chef or a seasoned culinary expert, the W10520792B is sure to play a pivotal role in your kitchen adventures.