KitchenAid W10520792B manual ICE Maker USE, How Your Ice Maker Works, Using the Controls

Page 15

Replace the Water Filter

To purchase a replacement water filter, see “Accessories.”

Replace the disposable water filter when indicated on the water filter status display or at least every 9 months. If the ice making rate decreases before the Replace Filter light illuminates, then replace the filter.

1.Locate the water filter compartment in the right-hand side of the control housing. See Step 3 in the “Install Water Filter” section.

2.Turn the water filter counterclockwise (to the left), and pull it straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling may occur.

3.Install the replacement water filter by following steps 2 through 5 in the “Install the Water Filter” section.

ICE MAKER USE

How Your Ice Maker Works

When you first start your ice maker, the water pan will fill and the system will rinse itself before starting to make ice. The rinsing process takes about 5 minutes.

Under normal operating conditions, the ice maker will cycle at preset temperatures. The ice level sensor located in the ice storage bin will monitor the ice levels.

IMPORTANT: If the water supply to the ice maker is turned off, be sure to set the ice maker control to OFF.

The Ice Making Process

1.Water is constantly circulated over a freezing plate. As the water freezes into ice, the minerals in the water are rejected. This produces a sheet of ice with a low mineral content.

2.When the desired thickness is reached, the ice sheet is released and slides onto a cutter grid. The grid divides the sheet into individual cubes.

3.The water containing the rejected minerals is drained after each freezing cycle.

4.Fresh water enters the machine for the next ice making cycle.

5.Cubes fall into the storage bin. When the bin is full, the ice maker shuts off automatically and restarts when more ice is needed. The ice bin is not refrigerated, and some melting will occur. The amount of melting varies with room temperature.

NOTE: As the room and water temperatures vary, so will the amount of ice produced and stored. This means that higher operating temperatures result in reduced ice production.

Using the Controls

1.To start ice production, press ON/OFF.

2.To stop ice maker operation, press ON/OFF.

NOTES:

Pressing the On/Off button does not shut off power to the ice maker.

Allow 24 hours to produce the first batch of ice. Discard the first 2 batches produced.

Max Ice Mode

Select the Max Ice feature when you have an upcoming need for a large amount of ice and the ice bin is low or empty. Max Ice mode will produce a greater quantity of ice in a 24-hour period.

Press MAX ICE while the ice maker is on. The indicator light will illuminate.

Press MAX ICE again to turn off the Max Ice feature. The indicator light will turn off.

The Max Ice mode will be on when you first turn on the product. It will turn off after 24 hours. To turn Max Ice back on, press MAX ICE.

15

Image 15
Contents Use & Care Guide Manual de uso y cuidadoGuide d’utilisation et d’entretien Table of Contents ÍndiceTable DES Matières ICE Maker Safety Installation InstructionsTools and Parts Custom Panel Dimensions Location Requirements Unpack the Ice MakerConnect Water Supply Electrical RequirementsWater Supply Requirements Vacation or Extended Time Without UseDrain Pump Installation Rear ViewKit Contains Water Supply Line If Ice Maker Is Currently InstalledDrain Pump Installation Drain CapVent Tube Drain Pump Mounting Tab SlotSide View Connecting the DrainDrain Connection Gravity Drain SystemOption 2 With Hinge-Side Spacer Install Custom Overlay PanelDoor Reversal-Side Swing Only Option 1-Without Hinge-Side SpaceReplace Door Remove Stainless Steel Door Wrap Panel on some modelsDoor Stop and End-Cap Reversal Reverse HingesReverse Door Catch LevelingTop Hinge Bottom HingeInstall the Water Filter Water Filtration SystemWater Filter Status Light Using the Controls ICE Maker USEHow Your Ice Maker Works Cleaning ICE Maker CareNormal Sounds Interior Components Condenser Dirty or Clogged CondenserFor Ice Makers with a Drain Pump Installed Vacation and Moving CareTo Shut Down the Ice Maker Ice Maker Seems Noisy TroubleshootingIce Maker Operation Ice Maker Will Not OperateIce Production Ice QualityIce Maker Runs But Produces No Ice For further assistance If you need replacement partsU.S.A CanadaAffresh* Stainless Steel Cleaner Performance Data SheetAccessories CleanerThis limited warranty does not cover Kitchenaid ICE Maker WarrantyPage Seguridad DE LA Fábrica DE Hielo Instrucciones DE InstalaciónHerramientas y piezas Dimensiones del panel hecho a la medida Requisitos de ubicación Desempaque la fábrica de hieloConexión del suministro de agua Requisitos eléctricosRequisitos del suministro de agua Vacaciones o tiempo prolongado sin usoEl juego contiene Instalación de la bomba de desagüeConexión de la tubería de agua Vista posteriorInstalación de la bomba de desagüe Si la fábrica de hielo ya está instaladaTapa de desagüe Línea de suministro de aguaBomba de desagüe instalada Tubo de desagüeRanura de la lengüeta de montaje de la bomba de desagüe Ubicaciones de las piezasVista lateral Conexión del desagüeTubo de ventilación Sistema de desagüe por gravedadInstale el panel de revestimiento hecho La medida Sistema de la bomba de desagüe en algunos modelosConexión del desagüe Llave de tuercas de ¹⁄₄ Destornillador Phillips Bisagra inferior Inversión de las bisagrasCómo volver a colocar la puerta Bisagra superiorInstalación del filtro de agua NivelaciónSistema de filtración de agua Cómo invertir el seguro de la puertaReemplazo del filtro de agua Luz de estado del filtro de aguaProceso de elaboración de hielo USO DE LA Fábrica DE HieloCómo funciona su fábrica de hielo Uso de los controlesCuidado DE LA Fábrica DE Hielo Sonidos normalesLimpieza Condensador Un condensador sucio u obstruido Tornillo Espaciador de plástico Rejilla de corte Componentes interioresPara apagar la fábrica de hielo Cuidado durante las vacaciones y mudanzasSolución DE Problemas Funcionamiento de la fábrica de hieloLa fábrica de hielo no funciona Producción de hielo Calidad del hieloLa fábrica de hielo funciona pero no produce hielo Si necesita piezas de repuesto Problemas de plomeríaAyuda O Servicio Técnico En los EE.UULimpiador Hoja DE Datos DEL RendimientoAccesorios Filtro de aguaEsta garantía limitada no cubre Garantía DE LA Fábrica DE Hielo DE KitchenaidPage Instructions D’INSTALLATION Sécurité DE LA Machine À GlaçonsOutillage et pièces Dimensions du panneau personnalisé Nettoyage avant l’utilisation Exigences d’emplacementDéballage de la machine à glaçons Enlèvement des matériaux d’emballageRaccordement à la canalisation d’eau Spécifications électriquesSpécifications de l’alimentation en eau Vacances ou longue période d’inutilisationVue arrière Raccordement du tuyau d’eau Installation de la pompe de vidangeBouchon de vidange Si la machine à glaçons est installéeInstallation de la pompe de vidange Contenu de l’ensembleEncoche de patte de montage de la pompe de vidange Pompe de vidange installéeTube de vidange Position des piècesVue latérale Raccordement au drain de vidangeTube de ventilation Vidange par gravitéInstallation du panneau décoratif personnalisé Système avec pompe de vidange sur certains modèlesRaccordement du drain de vidange Inoxydable Option 2-Avec cale despacement côté charnièreInversion du sens de montage des charnières Réinstallation de la porteRéinstallation du revêtement de porte sur certains modèles Inversion du sens dinstallation de la gâche de porteInstaller le filtre à eau NivellementSystème de filtration d’eau Témoin lumineux du filtre à eau Remplacement du filtre à eauUtilisation DE LA Machine À Glaçons Fonctionnement de la machine à glaçonsSons normaux Utilisation des commandesMode Max Ice glaçons max Alarme de porte entrouverteSystème de la machine à glaçons Entretien DE LA Machine À GlaçonsNettoyage Surfaces extérieuresComposants intérieurs Précautions à prendre avant les vacances ou un déménagement Arrêt de la machine à glaçonsMachine à glaçons avec pompe de vidange La machine à glaçons ne fonctionne pas DépannageProduction de glaçons Problèmes de plomberie Au Canada Assistance OU ServiceAccessoires Aux États-UnisSystème de filtration d’eau de la machine à glaçons Feuille DE Données SUR LA PerformanceLa présente garantie limitée ne couvre pas Garantie DE LA Machine À Glaçons KitchenaidW10520792B

W10520792B specifications

The KitchenAid W10520792B is an innovative component designed to elevate your culinary experience. This replacement part is particularly known for its reliability and efficiency, ensuring that your KitchenAid appliances function optimally. One of the main features of the W10520792B is its compatibility with various KitchenAid models, which makes it a versatile choice for users seeking to maintain their kitchen equipment in peak condition.

One notable characteristic of the W10520792B is its durable construction. Made from high-quality materials, it is designed to withstand the rigors of daily cooking tasks, providing longevity and consistent performance. This durability means that home chefs can rely on this part to perform under pressure, whether mixing, kneading, or whipping.

The W10520792B showcases KitchenAid's commitment to innovative design. The part utilizes advanced manufacturing techniques to ensure precision, which contributes to the overall efficiency of KitchenAid appliances. This attention to detail not only enhances the functionality of the equipment but also allows users to enjoy a more seamless cooking experience.

Another essential technology found within the W10520792B is its user-friendly installation process. Designed with the homeowner in mind, this component can typically be replaced without the need for professional assistance, saving both time and money. Clear instructional guidelines usually accompany the part, enabling even less experienced users to successfully complete the replacement with ease.

Moreover, the W10520792B is part of KitchenAid's commitment to sustainability. The materials used are often environmentally friendly, ensuring that customers can maintain their appliances while being conscious of their ecological footprint. This quality appeals to consumers who value both performance and environmental responsibility in their kitchen tools.

In summary, the KitchenAid W10520792B is an essential component that embodies quality, durability, and innovation. Its compatibility with various models, user-friendly installation, and sustainable materials make it an excellent choice for maintaining the high performance of KitchenAid appliances. Home cooks can rely on this part to enhance their cooking experience, allowing them to create delicious meals with confidence. Whether you are an aspiring chef or a seasoned culinary expert, the W10520792B is sure to play a pivotal role in your kitchen adventures.